kenwood 430 manual

The Kenwood 430 is a high-performance audio receiver with AM/FM tuner, multiple audio inputs, speaker outputs, tone controls, remote control capability, and advanced audio processing. Designed for home audio systems with 100W per channel output, Dolby Digital decoding, and multiple connectivity options. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Main receiver unit, Remote Control, AM/FM antenna terminals, Speaker outputs, Audio input jacks, Headphone jack, Power connector.

Feature	Description
AM/FM antenna terminals	For external AM/FM antenna connections
Speaker outputs	For connecting left and right speakers
Audio input jacks	For CD player, tape deck, and auxiliary devices
Headphone jack	For private audio listening
AC power connector	For power connection
Remote sensor	For receiving remote control signals
POWER	Turns receiver on/off
VOLUME	Adjusts audio output level
INPUT SELECT	Selects between different audio sources
TONE CONTROLS	Adjusts bass and treble levels

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

1. Connect speakers: Attach speaker wires to appropriate terminals (red/black).
2. Connect audio sources: Use audio input jacks for CD player, tape deck, etc.
3. Connect antennas: Attach AM loop antenna and FM wire antenna.
4. Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block air vents. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

1. Set input source: Press INPUT SELECT to choose desired audio source.
2. Adjust volume: Use VOLUME control to set comfortable listening level.
3. Tune radio: Use TUNING control to find AM/FM stations.
4. Set tone controls: Adjust BASS and TREBLE to preference.

CAUTION! Ensure proper speaker connections before powering on.

Specifications

• Power Output: 100W per channel (8 ohms).
• Frequency Response: 20Hz - 20kHz.
• Total Harmonic Distortion: Less than 0.08%.
• Input Sensitivity: 200mV.
• Signal-to-Noise Ratio: Better than 85dB.
• Tuner Section: AM/FM with 30 station presets.
• Audio Inputs: CD, TAPE, AUX, PHONO.
• Power Requirements: 120V AC, 60Hz.
• Dimensions: 17" W × 6" H × 15" D.

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECT, BASS, TREBLE, BALANCE, TUNING.

Remote: POWER, VOLUME, MUTE, INPUT SELECT, TUNING, PRESET buttons.

Tone Controls: BASS (±10dB), TREBLE (±10dB). Balance: Adjusts left/right speaker balance. Tuner: Manual tuning and 30 station presets. Input Selection: CD, TAPE, AUX, PHONO, TUNER.

Connecting Devices

Audio Inputs: CD, TAPE, AUX, PHONO. Speaker Outputs: Left and right channels.

1. Turn off receiver before connecting devices.
2. Match audio cables to appropriate input jacks.
3. Ensure proper speaker wire polarity.
4. Select input source via INPUT SELECT.

Tip: Use high-quality cables for best audio performance.

Audio Operation

Supports various audio sources and playback modes.

1. Select source: Press INPUT SELECT for desired input.
2. Adjust volume: Use VOLUME control or remote.
3. Tone adjustment: Set BASS and TREBLE to preference.
4. Radio operation: Tune manually or use presets.
5. Mute function: Press MUTE to temporarily silence audio.
6. Balance control: Adjust left/right speaker balance.
7. Headphone use: Plug headphones into front jack.

WARNING! Do not operate at maximum volume for extended periods.

Advanced Features

Station Presets: Store up to 30 AM/FM stations. Tone Defeat: Bypass tone controls for pure audio. Loudness: Compensates for low-volume listening.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth; avoid liquids. Keep vents clear for proper ventilation.

CAUTION! Do not use chemical cleaners; keep away from moisture.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. Copyright © 2006 Kenwood; all rights reserved. For technical support, visit www.kenwood.com or contact 1-800-536-9663.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power connection; try different outlet.
No sound	Volume/mute/speakers	Check volume setting; ensure mute is off; verify speaker connections.
Poor radio reception	Antenna/position	Check antenna connections; reposition antennas.
Distorted sound	Input level/speakers	Reduce input level; check speaker impedance.
Remote not working	Batteries/obstacles	Replace batteries; ensure clear path to sensor.

Reset: Disconnect power for 30 seconds then reconnect.

Service: 1-800-536-9663; www.kenwood.com