Kenwood AT 200 Manual

The Kenwood AT 200 is a high-performance audio receiver with AM/FM tuner, multiple audio inputs, digital signal processing, remote control, and advanced connectivity options. Featuring 200 watts RMS power output, Dolby Digital decoding, and customizable audio settings, this receiver delivers exceptional sound quality for home entertainment systems. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Configuration 8. Advanced Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main receiver unit, Remote Control, AM/FM antenna inputs, Multiple audio inputs, Speaker terminals, Digital optical input.

Feature	Description
Power Output	200 watts RMS per channel
AM/FM Tuner	Digital tuning with preset memory
Audio Inputs	RCA, optical, coaxial digital inputs
Speaker Terminals	Binding posts for 2-8 ohm speakers
Remote Control	Full-function infrared remote
DSP Modes	Multiple sound field presets
Headphone Jack	3.5mm stereo headphone output
Power Switch	Main power on/off control
Volume Control	Digital encoder with mute function
Input Selector	Source selection dial

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

Connect speakers: Use speaker wire to connect to binding posts, observing polarity.
Connect audio sources: Use RCA cables for analog sources, optical for digital sources.
Connect antennas: Attach AM loop antenna and FM dipole antenna.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

Set input sources: Assign names to each input for easy identification.
Program radio stations: Use auto-scan to find and store AM/FM stations.
Configure audio settings: Set bass, treble, and balance to preference.
Calibrate speakers: Use built-in test tone for level matching.

CAUTION! Ensure all connections are secure before powering on.

Specifications

Power Output: 200 watts RMS per channel (8 ohms)
Frequency Response: 10Hz - 100kHz (+0/-3dB)
Total Harmonic Distortion: <0.05%
Signal-to-Noise Ratio: >100dB
Input Sensitivity: 200mV (line), 2.5mV (phono)
Digital Inputs: Optical, coaxial
Analog Inputs: 4 line-level, 1 phono
Power Requirements: 120V AC, 60Hz
Dimensions: 17.1" W × 6.2" H × 15.4" D

Controls and Settings

Front Panel: POWER, INPUT SELECTOR, VOLUME, BASS, TREBLE, BALANCE, TUNING.

Remote: POWER, INPUT SELECT, VOLUME UP/DOWN, MUTE, TUNING, PRESETS, DSP MODE, SLEEP TIMER.

Audio Controls: Bass (±10dB), Treble (±10dB), Balance (L/R), Loudness compensation. Tuner: Manual/auto tuning, 40 station presets. DSP: Hall, Theater, Stadium, Jazz Club sound modes. System: Sleep timer (15-90 minutes), display brightness, input naming.

Connecting Devices

Audio Sources: CD player, turntable, tape deck, digital audio players. Speakers: Main left/right speakers.

Turn off receiver before making connections.
Match cable types to appropriate inputs (phono to phono, etc.).
Select input via front panel dial or remote control.
Connect speakers observing correct polarity.

Tip: Use high-quality cables for best audio performance.

Audio Configuration

Customize sound to match room acoustics and personal preference.

Tone Controls: Adjust bass and treble using front panel knobs.
Balance: Set left/right balance for optimal stereo imaging.
Loudness: Engage for enhanced bass at low volume levels.
DSP Modes: Select from Hall, Theater, Stadium, Jazz Club presets.
Direct Mode: Bypass tone controls for pure signal path.
Speaker Setup: Configure for large or small speakers.
Subwoofer: Set crossover frequency if using external subwoofer.

WARNING! Avoid extreme tone control settings that may cause distortion.

Advanced Features

Sleep Timer: Automatically powers off after set time (15-90 min). Preset Memory: Store 40 AM/FM stations. Remote Control: Full system control from listening position. Phono Input: Built-in phono preamp for turntable connection.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Keep away from moisture and extreme temperatures.

CAUTION! Do not use chemical cleaners. Ensure proper ventilation during operation.

Regulatory Information

FCC Part 15: Class B digital device compliant with residential interference limits. CE certified for European markets. Copyright © 2025 Kenwood Corporation. All trademarks property of Kenwood. For technical support, visit www.kenwood.com or contact 1-800-536-9663.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power cord connection; test outlet; ensure power switch on.
No sound	Input selection/volume	Verify correct input selected; check volume level; ensure speakers connected.
Distorted sound	Overload/speakers	Reduce volume; check speaker impedance; verify source signal level.
Poor radio reception	Antenna placement	Reposition antennas; ensure proper connection; check for interference.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear path to IR sensor; check remote mode.

Reset: Disconnect power for 30 seconds to reset microprocessor.

Service: 1-800-536-9663; www.kenwood.com