Kenwood DNX 7200 Installation Manual

The Kenwood DNX 7200 is a premium navigation and multimedia receiver featuring GPS navigation, DVD playback, Bluetooth connectivity, USB input, iPod compatibility, and advanced audio controls. This manual provides comprehensive installation instructions, wiring diagrams, mounting procedures, and setup guidelines for proper installation and operation.

Features at a Glance

Key components: 6.95-inch touchscreen display, GPS navigation system, DVD player, Bluetooth module, USB port, iPod direct control, AM/FM tuner.

Package Contents

Unpack and verify all components before installation.

• Kenwood DNX 7200 main unit
• Wiring harness
• GPS antenna
• Remote control
• Installation hardware kit
• User manual and warranty card
• Navigation SD card
• USB extension cable

WARNING! Do not proceed with installation if any components are missing or damaged.

Installation Preparation

Prepare vehicle and gather necessary tools before beginning installation.

1. Disconnect negative battery terminal for safety.
2. Remove factory radio using appropriate removal tools.
3. Test fit DNX 7200 in dashboard opening.
4. Gather required tools: wire cutters, crimpers, electrical tape, multimeter.
5. Review vehicle wiring diagram for proper connections.

CAUTION! Always disconnect battery before working on electrical systems.

Wiring Connections

Connect wiring harness following color-coded system.

Tip: Use crimp connectors and heat shrink for reliable connections.

Mounting Procedure

Secure unit properly in dashboard.

1. Attach mounting sleeve to vehicle dash kit.
2. Connect all wiring harnesses before final mounting.
3. Slide unit into mounting sleeve until it clicks into place.
4. Install security bolt to prevent theft.
5. Attach trim bezel for finished appearance.

WARNING! Ensure all wiring is clear of moving parts and heat sources.

Antenna Connections

Connect various antennas for optimal performance.

1. GPS Antenna: Place on dashboard or roof for clear sky view.
2. AM/FM Antenna: Connect to vehicle antenna adapter.
3. SiriusXM Antenna: Optional satellite radio connection.
4. Backup Camera: Connect to rear camera input if equipped.

Note: GPS antenna requires clear view of sky for best reception.

System Setup

Configure basic settings after installation.

1. Reconnect battery and turn on unit.
2. Set language and region preferences.
3. Configure audio settings (balance, fader, EQ).
4. Set clock and time zone.
5. Calibrate touchscreen if necessary.
6. Program steering wheel controls if applicable.

CAUTION! Test all functions before final reassembly.

GPS Navigation Setup

Initialize and configure navigation system.

1. Ensure navigation SD card is properly inserted.
2. Allow GPS to acquire satellite signal (may take several minutes).
3. Set home address and frequent destinations.
4. Configure route preferences (fastest, shortest, avoid highways).
5. Update maps periodically for current information.

Tip: Initial GPS acquisition works best in open areas.

Bluetooth Pairing

Connect mobile devices for hands-free operation.

1. Enable Bluetooth on mobile device.
2. Access Bluetooth menu on DNX 7200.
3. Select "Add New Device" and search for available devices.
4. Select your device and enter PIN if required (usually 0000).
5. Test phone functions and audio streaming.

Note: Some features may require phone compatibility.

Specifications

• Display: 6.95-inch WVGA TFT LCD touchscreen
• Navigation: Garmin navigation with preloaded maps
• Media Support: DVD, DVD-R/RW, CD, CD-R/RW, MP3, WMA, AAC
• Output Power: 22W x 4 channels (MOSFET power IC)
• Preamp Outputs: 4V front, rear, subwoofer
• Bluetooth: Hands-free profile, audio streaming
• USB: Supports USB memory devices, iPod control
• Dimensions: 178mm (W) x 100mm (H) x 160mm (D)
• Power Supply: 12V DC negative ground

Troubleshooting

Reset: Press reset button or disconnect battery for 30 seconds.

Support: Kenwood Customer Service: 1-800-536-9663; www.kenwood.com