Kenwood Electric Heater Manual

The Kenwood Electric Heater is a high-efficiency portable heating unit with adjustable thermostat, multiple heat settings, safety tip-over switch, overheat protection, cool-touch exterior, energy-saving timer, remote control operation, LED display, and oscillation feature. Designed for rooms up to 150 square feet, operating on 120V AC power. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Heating element with ceramic technology, digital thermostat, safety features, remote control, LED display, oscillation mechanism.

Safety Precautions

Important safety instructions for proper operation and hazard prevention.

1. Keep combustible materials at least 3 feet from heater front and sides.
2. Do not use in bathrooms, laundry areas, or other high-humidity locations.
3. Ensure proper ventilation; do not block air intake or outlet vents.
4. Plug directly into wall outlet; avoid extension cords.
5. Always place on stable, level surface.

WARNING! Never leave heater unattended while operating. Keep away from children and pets. Do not cover heater during operation.

Installation & Placement

Proper placement ensures optimal performance and safety.

1. Unpack heater and remove all packaging materials.
2. Choose location with minimum 3-foot clearance from walls and furniture.
3. Place on hard, level surface away from foot traffic.
4. Ensure power cord is not pinched or damaged.
5. Plug into grounded 120V AC outlet.

CAUTION! Do not use in wet or damp areas. Avoid carpeted surfaces if possible.

Specifications

• Power Requirements: 120V AC, 60Hz
• Wattage: 750W (Low), 1500W (High)
• Heating Coverage: Up to 150 square feet
• Thermostat Range: 60°F to 90°F (15°C to 32°C)
• Timer: 1-12 hours programmable
• Oscillation: 70° automatic
• Safety Certifications: ETL, CSA approved
• Dimensions: 12" H x 8" W x 6" D
• Weight: 5.5 lbs
• Warranty: 1-year limited warranty

Controls and Operation

Front panel controls: POWER, TEMPERATURE (+/-), MODE, TIMER, OSCILLATION.

Operation Steps:

1. Press POWER button to turn on heater
2. Select heat mode: LOW, HIGH, or ECO
3. Set desired temperature using +/- buttons
4. Enable oscillation for wider heat distribution
5. Set timer for automatic shut-off (1-12 hours)
6. Heater will maintain set temperature automatically

Eco Mode: Automatically adjusts power to maintain comfort while saving energy.

Remote Control Functions

Remote control provides full operation from distance.

Battery: Requires 2 AAA batteries (not included). Replace when remote becomes unresponsive.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Unplug heater and allow to cool completely before cleaning
2. Wipe exterior with soft, dry cloth
3. Clean air intake and outlet vents with soft brush
4. Check power cord regularly for damage
5. Store in dry location when not in use

CAUTION! Never immerse heater in water or use liquid cleaners. Do not use abrasive materials.

Energy Saving Tips

Maximize efficiency and reduce energy consumption.

• Use ECO mode for automatic energy optimization
• Set thermostat to lowest comfortable temperature (68°F recommended)
• Use timer to prevent unnecessary operation
• Close doors and windows in heated room
• Use only in occupied rooms
• Combine with proper insulation for best results

Regulatory Information

This heater complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Copyright © 2025 Kenwood Appliances. For support, visit www.kenwoodappliances.com or contact 1-800-555-HEAT.

Troubleshooting

Reset Procedure: Unplug heater for 5 minutes, then restart.

Service: 1-800-555-HEAT; www.kenwoodappliances.com