Kenwood Heater EW7507EK Manual

The Kenwood Heater EW7507EK is a 2000W electric heater with three heat settings, adjustable thermostat, overheat protection, tip-over safety switch, cool-touch housing, portable design with carry handle, LED power indicator, and energy-saving features. Suitable for rooms up to 20m². Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Heating element with three power settings, adjustable thermostat control, safety protection systems, portable housing with carry handle.

Installation

Unpack and inspect contents. Place on stable, level surface.

1. Choose location: Place on flat, stable surface away from flammable materials.
2. Clearance requirements: Maintain minimum 1-meter clearance from walls and furniture.
3. Power connection: Plug directly into wall outlet; avoid extension cords.
4. Positioning: Ensure unit is upright and stable on floor surface.

WARNING! Do not place under shelves or near curtains. Keep away from water sources.

First-Time Setup

Position heater and connect to power source.

1. Placement: Ensure unit is on stable, level surface with adequate clearance.
2. Power connection: Plug into grounded 220-240V AC outlet.
3. Initial operation: Turn power dial to lowest setting for first use.
4. Thermostat setting: Adjust to desired temperature level.

CAUTION! Do not use in bathrooms or other high-moisture areas.

Specifications

• Power Rating: 2000W maximum
• Heat Settings: 3 levels (800W/1200W/2000W)
• Voltage: 220-240V AC, 50/60Hz
• Room Coverage: Up to 20 square meters
• Thermostat: Adjustable temperature control
• Safety Features: Overheat protection, tip-over switch
• Dimensions: Standard portable heater size
• Weight: Lightweight for easy portability
• Certification: CE, RoHS compliant

Controls and Settings

Front control panel: Power dial, thermostat control, mode selector.

Control Functions: Power dial (Off/Low/Medium/High), Thermostat dial (1-5 settings), Oscillation button, Timer setting, LED power indicator.

Operation: Turn power dial to desired heat setting. Adjust thermostat to maintain temperature. Use timer for automatic shut-off. Remote control functions mirror main controls.

Connecting to Power

Use grounded wall outlet only; avoid extension cords.

1. Ensure heater is turned OFF before plugging in.
2. Plug directly into 220-240V AC wall outlet.
3. Do not use with power strips or extension cords.
4. Check that outlet is properly grounded.

Tip: Use dedicated circuit if possible to avoid overloading.

Operation Modes

Three heating modes with adjustable thermostat.

1. Low setting: 800W for energy-saving operation
2. Medium setting: 1200W for balanced heating
3. High setting: 2000W for maximum heat output
4. Thermostat control: Adjust to maintain desired room temperature
5. Timer function: Set automatic shut-off from 1-8 hours
6. Oscillation: Wide-area heat distribution (if equipped)
7. ECO mode: Energy-saving operation (if available)

WARNING! Never leave heater unattended while in operation.

Safety Features

Overheat Protection: Automatic shut-off if internal temperature exceeds safe limits. Tip-over Switch: Cuts power if unit is knocked over. Cool-touch Housing: External surfaces remain safe to touch.

Care & Cleaning

Unplug and cool completely before cleaning. Wipe exterior with dry cloth. Do not immerse in water.

CAUTION! Never use abrasive cleaners or liquids. Store in dry location when not in use.

Regulatory Information

CE certified: Complies with European safety standards. RoHS compliant: Free of hazardous substances. For support, visit www.kenwood.com or contact customer service. Copyright © 2025 Kenwood.

Troubleshooting

Reset: Unplug for 10 minutes, then restart.

Service: Contact authorized Kenwood service center for repairs.