Kenwood KCA BT200 Manual

The Kenwood KCA BT200 is a Bluetooth adapter module designed for Kenwood car audio systems, enabling wireless audio streaming and hands-free calling functionality. Compatible with select Kenwood head units, it supports A2DP for stereo audio streaming, AVRCP for remote control, and HFP for hands-free communication. Below are key sections for features, installation, setup, operation, specifications, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Bluetooth Operation 8. Compatibility Information 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Bluetooth adapter module, connection cables, mounting hardware.

Feature	Description
Bluetooth version	Bluetooth 2.0 + EDR
Audio profiles	A2DP (stereo audio), AVRCP (remote control)
Phone profiles	HFP 1.0 (hands-free), PBAP (phonebook access)
Connection type	Wired connection to compatible Kenwood head unit
Wireless range	Up to 10 meters (33 feet)
Power supply	Powered through head unit connection
LED indicator	Shows connection status and pairing mode
Microphone	Built-in for hands-free calls
Audio quality	Supports high-quality stereo audio streaming
Compatibility	Select Kenwood KDC, KMR, and DDIN models

Installation

Unpack and inspect contents. Ensure vehicle is parked and ignition is off.

Disconnect negative battery terminal for safety.
Remove head unit from dashboard following vehicle-specific instructions.
Locate Bluetooth port on rear of compatible Kenwood head unit.
Connect KCA BT200 module to the designated port.
Route microphone cable to optimal position near driver.
Secure module in available space behind dashboard.
Reinstall head unit and reconnect battery.

WARNING! Professional installation recommended. Ensure proper grounding and secure connections.

First-Time Setup

Power on head unit; initialize Bluetooth connection.

Enable Bluetooth pairing mode: Press SOURCE until BT appears on display.
On mobile device, enable Bluetooth and search for devices.
Select "KENWOOD" from available devices list.
Enter pairing code "0000" if prompted.
Confirm successful connection via head unit display.
Test audio streaming and call functionality.

CAUTION! Do not operate mobile device while driving. Complete setup while parked.

Specifications

Bluetooth Version: 2.0 + EDR (Enhanced Data Rate)
Supported Profiles: A2DP, AVRCP, HFP 1.0, PBAP
Frequency Range: 2.4GHz ISM band
Wireless Range: Up to 10 meters (33 feet)
Audio Codec: SBC (Subband Coding)
Power Consumption: 5V DC through head unit
Operating Temperature: -20°C to 60°C (-4°F to 140°F)
Compatibility: Kenwood KDC-BT series, KMR-D series, select DDIN models
Dimensions: 80mm x 50mm x 20mm
Weight: 85g

Controls and Settings

Access Bluetooth functions through head unit controls. Source Selection: Press SOURCE to cycle to BT mode.

Head Unit Controls: SOURCE, VOLUME, TRACK/PRESET, PHONE, MUTE, MENU.

Bluetooth Settings: Pairing mode activation, device management, auto connection. Audio: Volume synchronization, audio quality settings. Phone: Call answer/end, voice dialing, phonebook access. Security: Pairing code (default 0000), device authorization.

Connecting Devices

Supports up to 5 paired devices; 1 active connection at a time.

Ensure head unit is in Bluetooth mode.
Enable Bluetooth on mobile device.
Select "KENWOOD" from available devices.
Enter "0000" if pairing code required.
Confirm connection on both devices.

Tip: For best performance, keep mobile device within 3 meters during initial pairing.

Bluetooth Operation

Supports audio streaming and hands-free calling.

Audio Streaming: Select BT source, play audio on connected device.
Track Control: Use TRACK buttons to skip forward/backward.
Volume Control: Adjust via head unit or connected device.
Call Management: Answer with PHONE button, end call with same.
Voice Dialing: Press and hold PHONE button for voice commands.
Phonebook Access: Sync contacts through PBAP profile.
Multiple Devices: Switch between paired devices via BT settings.
Auto Reconnect: Reconnects to last connected device on power on.

WARNING! Maintain attention on driving. Use voice commands when possible.

Compatibility Information

Compatible Kenwood Models: KDC-BT318U, KDC-BT338U, KDC-BT352U, KMR-D362BT, KDC-BT555U, DDX series with Bluetooth ready designation. Mobile Devices: iOS 4.0+, Android 2.3+, Windows Phone 8+, BlackBerry 7+.

Care & Maintenance

Keep module clean and dry. Avoid extreme temperatures and moisture.

CAUTION! Do not disassemble module. Keep away from liquids and direct sunlight.

Regulatory Information

FCC ID: AK8KCA-BT200. This device complies with Part 15 of FCC Rules. CE certified for European markets. Bluetooth SIG qualified. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized Kenwood service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No connection	Pairing mode/range	Ensure pairing mode active; move device closer; delete and re-pair.
Audio dropout	Interference/range	Reduce distance; check for wireless interference sources.
No sound	Volume/connection	Check volume settings; verify device connection; restart both devices.
Call quality issues	Microphone placement	Reposition microphone; check for obstructions; reduce background noise.
Device not recognized	Compatibility/power	Verify device compatibility; ensure proper power to head unit.

Reset: Disconnect battery for 30 seconds to reset module.

Service: Contact authorized Kenwood service center; www.kenwood.com