Kenwood KDC 200U Manual

The Kenwood KDC 200U is a single-DIN car stereo receiver featuring CD/MP3/WMA playback, AM/FM radio tuner with 18 FM/6 AM presets, front auxiliary input, detachable faceplate security, 4-channel 50W maximum power output, LCD display with adjustable illumination, bass/treble controls, loudness function, and clock/timer settings. Compatible with most vehicles requiring standard single-DIN installation. Below are key sections for features, installation, operation, settings, and troubleshooting.

Features at a Glance

Key components: Main unit with CD slot, detachable faceplate, remote control, wiring harness, mounting sleeve.

Installation

Prepare vehicle and gather necessary tools before installation.

1. Disconnect negative battery terminal for safety.
2. Remove existing stereo using removal tools if applicable.
3. Connect wiring harness: Match color-coded wires (red-ignition, yellow-battery, black-ground).
4. Connect antenna cable and speaker wires.
5. Slide unit into mounting sleeve and secure in dashboard.
6. Reconnect battery and test all functions.

WARNING! Always disconnect battery before installation to prevent electrical shorts.

Basic Operation

Power on unit by pressing POWER button.

1. Source selection: Press SOURCE to cycle between CD, Radio, AUX.
2. Volume control: Turn VOL knob or use remote control buttons.
3. CD operation: Insert disc for automatic playback; use SKIP for track navigation.
4. Radio: Press BAND to switch between AM/FM; use TUNE for station selection.
5. Preset stations: Hold number button to store current station.

NOTE: Unit will remember settings when powered off.

Specifications

• Power Output: 50W x 4 channels (max)
• Tuner Sensitivity: FM 10.8 dBf, AM 25 μV
• Frequency Response: 20Hz - 20kHz
• Signal-to-Noise Ratio: >80dB
• Supported Formats: CD, CD-R/RW, MP3, WMA
• Power Requirement: 12V DC negative ground
• Dimensions: 178mm(W) x 50mm(H) x 153mm(D)
• Operating Temperature: -20°C to +60°C

Controls and Settings

Front panel controls: POWER, VOL knob, SOURCE, EJECT, Function buttons.

Remote Control: POWER, VOLUME, MUTE, SOURCE, TRACK UP/DOWN, PRESET buttons.

Audio Settings: BASS (-10 to +10), TREBLE (-10 to +10), LOUDNESS (On/Off), BALANCE (L/R), FADER (F/R). Display: DIMMER (3 levels), CLOCK setting. Radio: LOCAL/DX reception, SEEK tuning, PRESET memory. CD: REPEAT, RANDOM, SCAN modes.

Audio Sources

CD: Insert disc label-side up. MP3/WMA: Supports folder navigation. AUX: Connect external device to front 3.5mm jack.

1. Select source using SOURCE button.
2. For CD: Automatic playback begins when disc is inserted.
3. For MP3: Use folder buttons to navigate file structure.
4. For AUX: Ensure external device volume is set appropriately.

Tip: Use random play for varied music selection.

Radio Operation

AM/FM tuner with automatic and manual tuning options.

1. Press BAND to select AM or FM.
2. Automatic tuning: Press and hold SEEK up/down.
3. Manual tuning: Press TUNE briefly to step through frequencies.
4. Store presets: Tune to desired station, hold number button (1-6/1-18) for 2 seconds.
5. Recall presets: Press corresponding number button briefly.

NOTE: Use LOCAL setting for strong stations only in urban areas.

Security Features

Detachable Faceplate: Remove when parked to deter theft. Security Code: Optional code can be set to prevent unauthorized use.

Care & Maintenance

Clean with soft, dry cloth only. Avoid chemical cleaners. Keep discs clean and free of scratches.

CAUTION! Do not use solvents or abrasive cleaners on unit surface.

Regulatory Information

FCC Part 15 compliant. This device complies with part 15 of FCC Rules. Operation subject to conditions: (1) device may not cause harmful interference, (2) device must accept any interference received. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized service centers.

Troubleshooting

Reset: Disconnect battery for 1 minute to reset unit.

Service: Contact authorized Kenwood service center for repairs.