Kenwood KDC MP208 Manual

The Kenwood KDC MP208 is a digital media receiver with CD/MP3/WMA playback, built-in amplifier, USB connectivity, front auxiliary input, detachable face security, and advanced audio controls. Features include 50W x 4 max power, high-power MOSFET amplifier, CD-R/RW compatibility, MP3/WMA ID3 tag display, and customizable sound settings. Below are key sections for features, installation, operation, settings, and troubleshooting.

1. Features at a Glance 2. Installation 3. Basic Operation 4. Specifications 5. Controls and Functions 6. Audio Settings 7. USB Playback 8. Security Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Digital media receiver, detachable faceplate, remote control, wiring harness, mounting sleeve.

Feature	Description
CD/MP3/WMA Playback	Plays CDs, MP3, and WMA files
USB Connectivity	Direct USB input for digital media
Front AUX Input	3.5mm auxiliary input for external devices
MOSFET Power	50W x 4 max power output
Detachable Face	Security feature with removable control panel
ID3 Tag Display	Shows track information for MP3/WMA files
Audio Controls	Bass, treble, balance, fader adjustments
Preset Memory	18 FM/6 AM station presets
Clock Display	Digital clock with dimmer function
Remote Control	Included wireless remote for all functions

Installation

Unpack and verify all components. Ensure proper vehicle compatibility.

Disconnect vehicle battery: Remove negative terminal for safety.
Remove existing radio: Use proper removal tools for your vehicle.
Connect wiring harness: Match wire colors and functions carefully.
Mount receiver: Secure in dash using mounting sleeve.
Reconnect battery: Test all functions before final assembly.

WARNING! Always disconnect battery before installation. Ensure proper grounding.

Basic Operation

Power on unit; attach faceplate if detached.

Source selection: Press SOURCE to cycle through modes (CD/USB/AUX/TUNER).
Volume control: Turn knob or use remote VOL+/- buttons.
Playback controls: PLAY/PAUSE, SKIP, SCAN for media playback.
Radio tuning: Manual tune or seek; store presets (18 FM/6 AM).
Display modes: Press DISP to cycle through clock and track info.

CAUTION! Do not operate while driving. Keep faceplate secure when installed.

Specifications

Power Output: 50W x 4 (Max), 22W x 4 (RMS)
Supported Media: CD, CD-R, CD-RW, MP3, WMA
Tuner Section: FM/AM with 18 FM & 6 AM presets
Frequency Response: 20Hz - 20kHz
Signal-to-Noise: 95dB (CD), 90dB (MP3)
USB Support: USB 2.0, up to 32GB
Audio Inputs: Front AUX (3.5mm), Rear RCA preouts
Power Requirement: 12V DC, negative ground
Dimensions: DIN size (178mm x 50mm)

Controls and Functions

Front Panel: POWER/VOLUME knob, SOURCE, BAND, SEEK/SKIP, DISP, AUX input.

Remote: POWER, VOLUME, MUTE, SOURCE, PRESET, SEEK/SKIP, PLAY/PAUSE, BAND.

Basic Functions: SOURCE selection, VOLUME control, SEEK tuning, PRESET memory, DISPLAY modes. Advanced: Audio settings (BASS/TREBLE/BAL/FAD), Loudness, EQ presets, Clock set, Dimmer control.

Audio Settings

Access audio menu by pressing and holding AUDIO/SETUP.

Bass/Treble: Adjust frequency response (-7 to +7 levels)
Balance/Fader: Control speaker output distribution
Loudness: Boost low frequencies at low volumes
EQ Presets: Select from FLAT, POP, ROCK, JAZZ, CLASSIC
Subwoofer: Adjust subwoofer level if connected

Tip: Reset to factory defaults by holding SETUP for 5 seconds.

USB Playback

Supports USB flash drives with MP3/WMA files.

Connect USB: Insert USB device into front port.
Select source: Press SOURCE until USB mode activates.
Navigation: Use folder up/down to browse directories.
Play modes: Repeat (1/ALL), Random, Scan functions.
File info: DISP shows ID3 tag information when available.

WARNING! Do not remove USB during playback. Format drives as FAT32.

Security Features

Detachable Faceplate: Remove for theft prevention. Security Code: 4-digit code prevents unauthorized use (default 0000).

Care & Maintenance

Clean with dry, soft cloth only. Avoid liquids and abrasive cleaners.

CAUTION! Do not use solvents. Store faceplate in protective case when removed.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Wiring/faceplate	Check connections; ensure faceplate attached properly
No sound	Mute/speakers	Check mute function; verify speaker connections
CD not playing	Disc/format	Clean disc; ensure compatible format (CD-R/RW)
USB not recognized	Format/capacity	Reformat as FAT32; check USB size limit (32GB)
Poor radio reception	Antenna/connection	Ensure antenna connected; check antenna amplifier

Reset: Disconnect battery for 1 minute to reset unit.

Service: Contact authorized Kenwood service center for repairs.