kenwood kdc mp342u manual pdf

The Kenwood KDC-MP342U is a CD receiver with USB connectivity, MP3/WMA playback capability, detachable faceplate security, 50W x 4 maximum power output, preset equalizer, and advanced audio controls. This manual covers installation, operation, features, troubleshooting, and specifications for optimal use.

Features at a Glance

Key components: CD receiver with USB port, detachable faceplate, remote control, preset EQ, and audio adjustments.

Installation

Proper installation ensures optimal performance and safety.

1. Disconnect vehicle battery negative terminal before installation.
2. Mount unit using DIN sleeve and mounting kit.
3. Connect wiring harness following color codes.
4. Connect antenna and USB extension cable if needed.
5. Reconnect battery and test unit operation.

WARNING! Always disconnect power before installation to prevent electrical shorts.

Basic Operation

Power on unit and follow these basic operations.

1. Source selection: Press SOURCE to cycle through CD, USB, Tuner, Aux.
2. Volume control: Use VOL knob or remote control.
3. Playback controls: PLAY, PAUSE, SKIP for media playback.
4. Radio tuning: Use TUNE or SEEK for station selection.
5. Preset stations: Store up to 18 FM and 6 AM stations.

NOTE: Unit will enter demo mode if not properly installed.

Specifications

• Power Output: 50W x 4 (Max), 22W x 4 (RMS)
• Supported Media: CD, CD-R, CD-RW, MP3, WMA
• USB Support: USB 2.0, up to 32GB
• Tuner Sensitivity: FM 10.3 dBf, AM 18 μV
• Frequency Response: 20Hz - 20kHz
• Signal-to-Noise: 95 dB (CD), 90 dB (USB)
• Separation: 60 dB
• Power Requirement: 14.4V DC (11-16V range)
• Dimensions: 178mm (W) x 50mm (H) x 153mm (D)

Controls and Functions

Front panel controls: POWER/VOL knob, SOURCE, BAND, TUNE, AUDIO, eject button.

Remote Control: POWER, VOLUME, MUTE, SOURCE, PRESET, PLAY/PAUSE, SKIP, BAND.

Display shows: Current source, track info, time, radio frequency, audio settings. Illumination can be adjusted in settings menu.

Audio Settings

Access audio settings by pressing AUDIO button.

1. Bass: Adjust low frequency response (-6 to +6)
2. Treble: Adjust high frequency response (-6 to +6)
3. Balance: Adjust left/right speaker balance
4. Fader: Adjust front/rear speaker balance
5. Loudness: Enhance bass at low volumes
6. EQ Presets: POP, ROCK, JAZZ, CLASSIC, FLAT

Tip: Reset to factory settings by holding AUDIO for 3 seconds.

USB Playback

USB device playback instructions.

1. Connect USB device to USB port.
2. Select USB as source.
3. Navigate folders using TUNE knob.
4. Play/Pause with center button.
5. Skip tracks with SKIP buttons.
6. Fast forward/rewind by holding SKIP.

NOTE: Some USB devices may require additional power.

Security Features

Detachable faceplate anti-theft system.

1. To remove: Press release button and slide faceplate off.
2. To attach: Align connectors and push until click.
3. Security code: Set 4-digit code in menu (default 0000).
4. If power disconnected, enter code to reactivate.

WARNING! Store faceplate in protective case when not in use.

Care & Maintenance

Proper care ensures longevity.

• Clean faceplate with soft, dry cloth only
• Avoid chemical cleaners and solvents
• Keep CDs and USB connectors clean
• Store unit in moderate temperatures
• Avoid moisture and extreme heat

CAUTION! Do not disassemble unit; no user-serviceable parts inside.

Regulatory Information

FCC Part 15 compliant. This device complies with part 15 of FCC rules. Operation subject to conditions: (1) device may not cause harmful interference, (2) device must accept any interference received. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact 1-800-536-9663.

Troubleshooting

Reset: Hold SOURCE while turning on to factory reset.

Service: 1-800-536-9663; www.kenwood.com