Kenwood KDC MP828 Manual

The Kenwood KDC MP828 is a high-performance car audio receiver featuring CD/MP3/WMA playback, AM/FM tuner with 18FM/6AM presets, detachable faceplate security, 4-channel 50W maximum power output, auxiliary input, CD changer control, loudness control, and advanced audio adjustments. Below are key sections for features, installation, operation, settings, and troubleshooting.

Features at a Glance

Key components: Main unit with detachable faceplate, remote control, wiring harness, mounting sleeve, user manual.

Installation

Professional installation recommended. Ensure vehicle is parked with ignition off.

1. Disconnect negative battery terminal for safety.
2. Remove existing stereo unit from dashboard.
3. Connect wiring harness following color-coded wires.
4. Slide unit into mounting sleeve and secure properly.
5. Reconnect battery and test all functions.

WARNING! Incorrect installation may damage unit or vehicle electrical system. Use proper tools and follow wiring diagram.

Basic Operation

Power on unit by pressing POWER button. Detach faceplate when leaving vehicle.

1. Source selection: Press SOURCE to cycle through CD, Tuner, Aux.
2. Volume control: Turn VOLUME knob or use remote control.
3. Station presets: Tune to desired station, press and hold preset button.
4. CD operation: Insert disc label-side up, unit auto-plays.
5. Clock setting: Press and hold CLOCK button, use tuning knob to set time.

CAUTION! Do not operate while driving if it distracts from road safety.

Specifications

• Power Output: 50W x 4 (Max), 22W x 4 (RMS)
• Frequency Response: 20Hz - 20kHz
• Signal-to-Noise Ratio: 105dB (CD)
• Preset Stations: 18 FM, 6 AM
• Supported Formats: CD, CD-R, CD-RW, MP3, WMA
• Power Requirement: 12V DC, negative ground
• Dimensions: 7" W x 2" H x 6" D
• Operating Temp: -4°F to 140°F (-20°C to 60°C)

Controls and Functions

Front Panel: POWER, EJECT, VOLUME knob, SOURCE, BAND, buttons for audio controls.

Remote Control: POWER, numeric buttons, volume controls, track selection, mute, display dimmer.

Audio Controls: BASS, TREBLE, BALANCE, FADER, LOUDNESS. Tuner: SEEK, SCAN, manual tuning, preset selection. CD: PLAY, PAUSE, STOP, PREV/NEXT track, random/repeat modes. Display: Clock, source indicator, track/time information.

Audio Settings

Access audio menu by pressing and holding AUDIO button.

1. Bass/Treble: Adjust from -7 to +7 levels
2. Balance: Adjust left/right speaker balance
3. Fader: Adjust front/rear speaker balance
4. Loudness: On/Off for bass enhancement
5. EQ Presets: Flat, Rock, Pop, Jazz, Classical
6. Subwoofer Control: Level and phase adjustment

Tip: Reset to factory settings by holding RESET button with small pin.

Playing Media

Supports audio CDs, MP3 CDs, WMA CDs.

1. Insert disc: Press EJECT, insert disc label-up, close tray.
2. Playback: Unit auto-plays; use PREV/NEXT for track selection.
3. MP3 Navigation: Use folder buttons to navigate directories.
4. Repeat/Random: Press RPT for repeat, RDM for random play.
5. Fast Forward/Rewind: Press and hold FF/REW buttons.
6. Pause: Press PAUSE during playback.
7. Eject: Press EJECT to remove disc.

WARNING! Do not use damaged or irregular shaped discs. Keep discs clean.

Security Features

Detachable Faceplate: Remove when leaving vehicle to prevent theft. Security Code: 4-digit code can be set to disable unit if stolen.

Maintenance

Clean unit with soft, dry cloth only. Do not use chemicals or solvents.

CAUTION! Do not expose to extreme temperatures or moisture. Store faceplate in protective case.

Regulatory Information

FCC Part 15: Class B digital device compliant. CE marked for European markets. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized service centers.

Troubleshooting

Reset: Use reset button on faceplate with small pin.

Service: Contact authorized Kenwood service center for repairs.