Kenwood KDC X589 Manual

The Kenwood KDC X589 is a high-performance car stereo receiver featuring CD/MP3/WMA playback, built-in MOSFET 50Wx4 amplifier, detachable faceplate security, advanced audio controls with 3-band parametric EQ, Sirius Satellite Radio ready, iPod direct control, Bluetooth connectivity, USB input, auxiliary input, and customizable illumination. Below are key sections for features, installation, operation, settings, and troubleshooting.

1. Features at a Glance 2. Installation 3. Basic Operation 4. Specifications 5. Controls and Functions 6. Audio Settings 7. Bluetooth Connectivity 8. USB and iPod Operation 9. Security Features 10. Troubleshooting

Features at a Glance

Key components: Main unit with detachable faceplate, remote control, wiring harness, mounting sleeve, user manual.

Feature	Description
Power Output	MOSFET 50W x 4 channels (max)
CD Playback	CD, CD-R, CD-RW, MP3, WMA
Bluetooth	Hands-free calling and audio streaming
USB Input	Direct control for USB devices
iPod Control	Direct connection and control
Auxiliary Input	3.5mm jack for external audio sources
Sirius Ready	Satellite radio compatible (tuner required)
Security	Detachable faceplate with carrying case
EQ Controls	3-band parametric equalizer
Illumination	Customizable button and display colors

Installation

Professional installation recommended. Ensure vehicle is off during installation.

Disconnect negative battery terminal for safety.
Remove existing stereo and prepare wiring harness.
Connect wiring harness following color codes: Yellow (constant power), Red (ignition power), Black (ground).
Connect speaker wires and antenna cable.
Slide unit into dashboard and secure with mounting sleeve.
Reconnect battery and test all functions.

WARNING! Always disconnect battery before installation. Incorrect wiring may damage unit or vehicle electrical system.

Basic Operation

Power on unit by pressing SRC button. Detach faceplate when parked for security.

Source Selection: Press SRC to cycle through AM/FM, CD, USB, Bluetooth, Aux.
Volume Control: Turn knob or use remote control volume buttons.
Track Selection: Use << and >> buttons for previous/next tracks.
Mode Selection: Press FUNCTION for additional options per source.
Mute: Press MUTE button for instant audio silence.

CAUTION! Do not operate while driving. Set all controls before driving.

Specifications

Power Output: 50W x 4 (MOSFET power IC)
Frequency Response: 10Hz - 20kHz
Signal-to-Noise Ratio: 105dB (CD)
Preset Stations: 18 FM, 6 AM
CD Compatibility: CD, CD-R, CD-RW, MP3, WMA
USB Support: USB 2.0, up to 32GB
Bluetooth Profiles: HFP, A2DP, AVRCP
Power Requirement: 12V DC negative ground
Dimensions: DIN size (178mm x 50mm)

Controls and Functions

Front Panel: SRC, POWER/VOLUME knob, MUTE, FUNCTION, <<, >>, USB port, auxiliary input.

Remote Control: Power, Volume, Mute, Track selection, Preset buttons, Mode selection.

Source Controls: AM/FM tuning and presets, CD playback controls, USB navigation, Bluetooth pairing. Audio Controls: Bass, Midrange, Treble, Loudness, Balance, Fader. System Settings: Clock, Display dimmer, Button illumination, Security code.

Audio Settings

Access audio menu by pressing and holding AUDIO button.

Equalizer: 3-band parametric EQ with adjustable frequency and Q factor
Loudness: On/Off for enhanced low-volume listening
Balance/Fader: Adjust speaker balance and front/rear fader
Subwoofer Control: Level and phase adjustment (if connected)
Time Alignment: Adjust audio timing for optimal sound staging

Tip: Save settings by pressing and holding desired preset button.

Bluetooth Connectivity

Pair mobile devices for hands-free calling and audio streaming.

Enable Bluetooth on mobile device.
Press SOURCE until BT appears on display.
Search for "KENWOOD" on mobile device.
Enter PIN "1234" when prompted.
Confirm pairing on both devices.
For calls: Use phone buttons or unit's mute function.
For music: Control playback from unit or mobile device.

WARNING! Do not make calls while driving. Pull over safely if necessary.

USB and iPod Operation

Connect USB devices or iPod directly to front panel port.

Connect device using appropriate cable.
Press SOURCE until USB mode activates.
Navigate folders using << and >> buttons.
Play/Pause with center button.
Fast forward/rewind by holding << or >>.
For iPod: Full control of playlists, artists, albums.
Charging: Devices charge while connected.

CAUTION! Do not disconnect USB devices during playback. Ensure proper file format compatibility.

Security Features

Detachable faceplate: Remove when parked to prevent theft. Security code: 4-digit code required if power is disconnected.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Wiring/connections	Check fuse, wiring connections, battery connection
No sound	Settings/speakers	Check volume, mute, speaker connections, fader settings
CD won't play	Disc/format	Check disc for damage, ensure compatible format, clean lens
Bluetooth not connecting	Pairing/range	Delete old pairing, ensure within range, restart both devices
USB not recognized	Device/format	Check device compatibility, reformat to FAT32, try different cable

Reset: Hold reset button for 5 seconds with unit off.

Service: Contact authorized Kenwood service center or visit www.kenwood.com