Kenwood KR 5400 Manual

The Kenwood KR 5400 is a high-quality stereo receiver featuring AM/FM tuner, phono input, tape monitor, loudness control, and multiple audio inputs. With 40 watts per channel RMS power output, this receiver delivers exceptional sound quality for home audio systems. Below are key sections for features, installation, operation, specifications, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Components 7. Tuner Operation 8. Audio Controls 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: AM/FM stereo tuner, phono input, tape monitor, loudness control, speaker selector, tone controls.

Feature	Description
Power Output	40 watts per channel RMS (8 ohms)
Tuner Section	AM/FM stereo with quartz PLL synthesis
Phono Input	MM cartridge compatible
Tape Monitor	Two tape decks with dubbing capability
Loudness Control	Compensates for low volume listening
Tone Controls	Bass and treble adjustment
Speaker Selector	A/B speaker switching
Headphone Jack	For private listening
Input Selector	Phono, Tuner, Aux, Tape 1, Tape 2
Power Switch	Main power on/off

Installation

Unpack and inspect contents. Place on stable, level surface.

Connect speakers: Use speaker wire to connect to A or B speaker terminals.
Connect turntable: Use phono input for magnetic cartridge turntables.
Connect tape decks: Use tape 1 and tape 2 inputs/outputs.
Connect auxiliary sources: Use aux input for CD players, etc.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings.

First-Time Setup

Power on receiver; follow initial setup procedure.

Set input selector to desired source (phono, tuner, aux, tape).
Adjust volume to minimum before powering on.
Tune FM stations: Use tuning knob or seek function.
Set tone controls to flat position for initial listening.
Select speaker output (A, B, or A+B).

CAUTION! Do not connect speakers while power is on.

Specifications

Power Output: 40 watts per channel RMS at 8 ohms
Frequency Response: 20Hz - 20kHz ±1dB
Total Harmonic Distortion: 0.08% at rated power
Input Sensitivity: Phono: 2.5mV, Aux: 150mV
Signal-to-Noise Ratio: Phono: 76dB, Aux: 90dB
Tuner Section: FM sensitivity 11.2dBf
Power Requirements: 120V AC, 60Hz
Dimensions: 17" W × 5" H × 13" D
Weight: 18.7 lbs

Controls and Settings

Front panel controls: Power switch, input selector, volume, balance, tone controls, loudness, speaker selector.

Rear Panel: Speaker terminals, phono input, tape inputs/outputs, aux input, AC power cord.

Tone Controls: Bass ±10dB at 100Hz, Treble ±10dB at 10kHz. Loudness: Compensates for Fletcher-Munson curves. Balance: Adjusts left/right channel balance. Input Selector: Phono, Tuner, Aux, Tape 1, Tape 2.

Connecting Components

Speaker connections: Use A or B speaker terminals. Source connections: Phono, aux, tape decks.

Turn off power before making connections.
Match cable colors (red to red, white to white).
Ensure secure connections to prevent hum or noise.
Use proper gauge speaker wire for your setup.

Tip: Keep signal cables away from power cords to reduce interference.

Tuner Operation

AM/FM stereo tuner with manual and automatic tuning.

Select Tuner on input selector.
Use tuning knob for manual station selection.
FM stereo indicator lights when stereo broadcast is received.
Use signal strength meter for optimal antenna positioning.
For AM, rotate antenna for best reception.

Note: FM antenna connection required for proper reception.

Audio Controls

Tone controls: Bass and treble adjustment. Loudness: Enhances bass at low volumes. Balance: Adjusts left/right channel balance.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; avoid liquids.

CAUTION! Do not use chemical cleaners; keep away from moisture.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No sound	Speaker connections/power	Check speaker wires; ensure power is on; verify input selection.
Hum or noise	Grounding/cables	Check ground connections; separate signal and power cables.
Poor FM reception	Antenna/positioning	Adjust FM antenna; check antenna connection.
One channel silent	Balance/speaker	Check balance control; verify speaker connection.
Distorted sound	Overload/settings	Reduce volume; check source level; verify tone settings.

Service: Contact authorized Kenwood service center for repairs.