Kenwood KR 7600 Manual

The Kenwood KR 7600 is a high-performance stereo receiver featuring 60 watts per channel RMS power, quartz PLL synthesized tuning, 8 FM/8 AM station presets, loudness control, tape monitoring, tone controls, and multiple audio inputs. Below are key sections for features, installation, operation, specifications, and troubleshooting.

1. Features at a Glance 2. Installation 3. Operation 4. Specifications 5. Controls and Functions 6. Connecting Components 7. Tuning and Presets 8. Audio Settings 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Power amplifier, tuner section, input/output terminals, front panel controls.

Feature	Description
Power Output	60 watts per channel RMS (8 ohms)
Tuning System	Quartz PLL synthesized tuning
Preset Stations	8 FM and 8 AM station presets
Inputs	Phono, CD, Tape 1, Tape 2, Aux
Outputs	Speaker A/B, headphones, tape record
Tone Controls	Bass and treble adjustment
Loudness Control	Compensates for low volume listening
Tape Monitoring	Dubbing and monitoring capabilities
Power Requirements	120V AC, 60Hz
Dimensions	Standard component width

Installation

Unpack and inspect contents. Place on stable, level surface.

Connect speakers: Use speaker wire to connect to Speaker A/B terminals.
Connect audio sources: Use appropriate cables for phono, CD, tape decks.
Connect antenna: FM antenna to FM terminal, AM antenna to AM terminal.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings.

Operation

Power on receiver; select input source.

Select input: Choose PHONO, CD, TAPE, or AUX as needed.
Adjust volume: Use volume control knob.
Tune stations: Use tuning buttons or presets.
Adjust tone: Use bass and treble controls.

CAUTION! Do not operate at maximum volume for extended periods.

Specifications

Power Output: 60 watts per channel RMS (8 ohms)
Frequency Response: 20Hz - 20kHz
Total Harmonic Distortion: 0.08%
Signal-to-Noise Ratio: 75dB (phono)
Input Sensitivity: Phono: 2.5mV, CD/Aux: 150mV
Tuning Range: FM: 87.5-108MHz, AM: 530-1710kHz
Preset Memory: 8 FM, 8 AM stations
Power Consumption: 180 watts maximum
Dimensions: 17-1/8" W × 5-1/4" H × 13-3/8" D
Weight: 21.2 lbs

Controls and Functions

Front Panel: POWER, VOLUME, INPUT SELECTOR, TUNING, BASS, TREBLE, LOUDNESS, SPEAKER SELECTOR.

Rear Panel: Speaker terminals, input/output jacks, antenna terminals, AC power cord.

Input Selection: PHONO, CD, TAPE 1, TAPE 2, AUX. Tone Controls: Bass ±10dB, Treble ±10dB. Speaker Selection: A, B, A+B. Loudness: On/Off switch for bass boost at low volumes.

Connecting Components

Speakers: Use 16-gauge or larger speaker wire. Audio Sources: RCA cables for phono, CD, tape decks.

Turn off power before connecting components.
Match cables to appropriate input jacks.
Ensure secure connections.
Connect FM antenna for optimal reception.

Tip: Use high-quality cables for best audio performance.

Tuning and Presets

Quartz PLL synthesized tuning with preset memory.

Select FM or AM band.
Use TUNE buttons to find desired station.
Press MEMORY button.
Select preset number (1-8).
Press MEMORY again to store.
Recall presets using numbered buttons.

Note: Presets are maintained when power is off.

Audio Settings

Tone Controls: Adjust bass and treble to preference. Loudness: Engages bass boost at low volume levels. Balance: Adjust left/right channel balance. Speaker Selection: Choose speaker sets A, B, or both.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Clean controls with contact cleaner if needed.

CAUTION! Do not use liquid cleaners; avoid moisture exposure.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power connection; try different outlet.
No sound	Speaker connections	Verify speaker wires; check speaker selection.
Poor FM reception	Antenna	Adjust FM antenna; ensure proper connection.
Distorted sound	Input level/connections	Check input levels; verify cable connections.
Presets lost	Power interruption	Reprogram station presets.

Service: Contact authorized Kenwood service center for repairs.