Kenwood KR V6010 Manual

The Kenwood KR V6010 is a high-performance stereo receiver featuring Dolby Pro Logic surround sound, multiple audio inputs, AM/FM tuner with 30 station presets, remote control capability, and 100 watts per channel output. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Settings 8. Remote Control 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Dolby Pro Logic decoder, AM/FM tuner, multiple audio inputs, remote control, speaker terminals.

Feature	Description
Power Output	100 watts per channel (8 ohms)
Dolby Pro Logic	Surround sound decoding
AM/FM Tuner	30 station presets
Audio Inputs	CD, Tape, Phono, Video/Aux
Speaker Terminals	A/B speaker selection
Headphone Jack	For private listening
Remote Control	Included for full operation
Tone Controls	Bass and treble adjustment
Loudness	Enhanced bass at low volumes
Power Switch	Main power on/off

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

Connect speakers: Use speaker wire to connect to A/B terminals.
Connect audio sources: Use appropriate cables for CD player, tape deck, turntable.
Connect antenna: Attach AM loop antenna and FM wire antenna.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

Set speaker configuration: Choose A, B, or A+B speaker output.
Tune radio stations: Use auto-scan to preset AM/FM stations.
Adjust audio settings: Set bass, treble, and balance controls.
Configure surround sound: Set up Dolby Pro Logic for video sources.

CAUTION! Ensure all connections are secure before powering on.

Specifications

Power Output: 100W + 100W (8 ohms, 20Hz-20kHz)
Total Harmonic Distortion: 0.08%
Frequency Response: 10Hz-100kHz
Input Sensitivity: Phono: 2.5mV, CD: 200mV
Signal-to-Noise Ratio: Phono: 74dB, CD: 90dB
Tuner Section: AM/FM with 30 presets
Surround Sound: Dolby Pro Logic
Power Requirements: 120V AC, 60Hz
Dimensions: 17-1/8" W × 5-7/8" H × 14-3/4" D
Weight: 22.5 lbs

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECTOR, TONE CONTROLS, BALANCE, SPEAKER SELECTION.

Remote: POWER, VOLUME, MUTE, INPUT SELECTION, TUNER PRESETS, SURROUND MODE.

Audio Controls: BASS, TREBLE, LOUDNESS, BALANCE. Tuner: AUTO SCAN, MANUAL TUNING, PRESET MEMORY. Surround: Dolby Pro Logic mode selection, center channel level, delay settings.

Connecting Devices

Audio Inputs: PHONO, CD, TAPE, VIDEO/AUX. Speaker Outputs: A/B terminals.

Turn off receiver before connecting devices.
Match cables to appropriate inputs (phono to phono, etc.).
Connect speakers observing correct polarity.
Select input source via INPUT selector.

Tip: Use high-quality cables for best audio performance.

Audio Settings

Dolby Pro Logic surround sound for video sources.

Select VIDEO input for surround sound sources.
Engage Dolby Pro Logic mode for surround decoding.
Adjust center channel level for dialogue clarity.
Set surround delay for proper sound staging.
Use tone controls to customize sound character.
Engage loudness for enhanced bass at low volumes.
Balance control for left/right channel adjustment.

WARNING! Do not connect phono sources to non-phono inputs.

Remote Control

Full-function remote included. Replace batteries when performance decreases.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; no liquids or chemical cleaners.

CAUTION! Keep away from moisture and extreme temperatures. Ensure proper ventilation.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power connection; verify outlet function.
No sound	Speaker connections/volume	Check speaker wires; ensure volume not muted.
Poor radio reception	Antenna connection	Ensure antennas properly connected and positioned.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear path to sensor.
Distorted sound	Input level/speakers	Check input source levels; verify speaker impedance.

Reset: Disconnect power for 30 seconds to reset microprocessor.

Service: Contact authorized Kenwood service center for repairs.