Kenwood KR-V6020 Receiver Manual

The Kenwood KR-V6020 is a high-performance audio/video receiver featuring Dolby Pro Logic surround sound, multiple audio/video inputs, digital tuning with 30 presets, 100W per channel power output, remote control, and comprehensive audio adjustments. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio Modes and Effects 8. Remote Control Operation 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Dolby Pro Logic decoder, digital tuner with 30 presets, multiple audio/video inputs, remote control, front panel controls.

Feature	Description
Power Output	100W per channel (front), 30W (center), 30W (rear)
Audio Inputs	CD, TAPE, VCR, PHONO, VIDEO/AUX
Video Inputs	VCR, VIDEO/AUX, MONITOR OUT
Tuner	AM/FM with 30 station presets
Surround Modes	Dolby Pro Logic, Hall, Theater, Mono
Remote Control	Full-function infrared remote
Headphone Jack	3.5mm stereo headphone output
Tone Controls	Bass, Treble, Balance
AC Power	120V AC, 60Hz
Dimensions	17-1/4" W x 5-7/8" H x 14-3/8" D

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

Connect speakers: Match polarity (+ to +, - to -) for front, center, and rear channels.
Connect audio sources: Use appropriate input jacks for CD player, tape deck, turntable, etc.
Connect video sources: Use video inputs for VCR, DVD player, or other video components.
Connect antenna: Attach FM antenna and AM loop antenna.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings. Use correct speaker impedance (6-16 ohms).

First-Time Setup

Power on receiver; follow initial setup procedure.

Set speaker configuration: Adjust front, center, and rear speaker levels.
Program radio stations: Use auto-scan to find and store FM/AM stations.
Adjust audio settings: Set bass, treble, and balance to preference.
Configure surround sound: Select Dolby Pro Logic or other surround modes.
Test all inputs: Verify proper operation of connected components.

CAUTION! Do not connect speakers while receiver is powered on. Ensure all connections are secure.

Specifications

Power Output: 100W + 100W (front), 30W (center), 30W + 30W (rear)
Total Harmonic Distortion: 0.08% (1kHz)
Frequency Response: 10Hz - 50kHz (+1/-3dB)
Signal-to-Noise Ratio: 80dB (PHONO)
Input Sensitivity: 2.5mV (PHONO), 150mV (LINE)
Tuner Section: FM/AM with 30 presets
Surround Modes: Dolby Pro Logic, Hall, Theater, Mono
Power Requirements: 120V AC, 60Hz, 280W
Dimensions: 438 x 149 x 365 mm (W x H x D)
Weight: 8.8 kg

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECTOR, TUNER BAND, PRESET, BASS, TREBLE, BALANCE, SURROUND MODE.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, TUNER PRESETS, SURROUND MODES, numeric buttons.

Audio Controls: BASS (±10dB), TREBLE (±10dB), BALANCE (L/R). Surround Modes: Dolby Pro Logic, Hall, Theater, Mono. Tuner: Auto-scan, manual tuning, 30 presets. Input Selection: CD, TAPE, VCR, PHONO, VIDEO/AUX.

Connecting Devices

Audio: CD, TAPE, PHONO, VCR AUDIO. Video: VCR VIDEO, MONITOR OUT. Speakers: Front L/R, Center, Rear L/R.

Turn off receiver and all components before connecting.
Use high-quality cables for best performance.
Match input jacks to source components.
Connect speakers ensuring proper polarity.
Select input source via front panel or remote.

Tip: Use shielded cables for phono input to prevent hum and noise.

Audio Modes and Effects

Dolby Pro Logic: Creates surround sound from stereo sources. Hall: Simulates concert hall acoustics. Theater: Enhanced for movie viewing. Mono: Combines channels for mono sources.

Select surround mode: Press SURROUND button repeatedly to cycle through modes.
Adjust channel levels: Use test tone to balance front, center, and rear speakers.
Fine-tune effects: Adjust delay time and effect level for optimal sound.
Save settings: Most settings are maintained when power is turned off.

WARNING! Do not exceed maximum volume levels to prevent speaker damage.

Remote Control Operation

Full-function remote controls receiver and compatible Kenwood components.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; avoid liquids and aerosols.

CAUTION! Do not use abrasive cleaners. Keep away from moisture and extreme temperatures.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Kenwood Corporation. For support, contact authorized Kenwood service centers or visit www.kenwood.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power connection; verify outlet works; check fuse.
No sound	Speaker connections/mute	Check speaker wires; ensure mute is off; verify input selection.
Poor FM reception	Antenna placement	Extend FM antenna fully; reposition for better reception.
Remote not working	Batteries/obstacles	Replace batteries; ensure clear path to IR sensor.
Hum or noise	Grounding/cables	Check ground connections; use shielded cables; separate from power cords.
Overheating	Ventilation	Ensure adequate ventilation; clear vents of obstructions.

Reset: Disconnect power for 30 seconds to reset microprocessor.

Service: Contact authorized Kenwood service center for repairs.