Kenwood KR V6080 Manual

The Kenwood KR V6080 is a high-performance stereo receiver featuring Dolby Pro Logic surround sound, multiple audio inputs, AM/FM tuner with 30 station presets, remote control capability, and 100 watts per channel power output. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Main unit with Dolby Pro Logic decoder, Remote Control, AM/FM antenna terminals, multiple audio inputs, speaker terminals, headphone jack.

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

1. Connect speakers: Match polarity (+/-) for front, center, and rear speakers.
2. Connect antennas: AM loop antenna and FM wire antenna to respective terminals.
3. Connect audio sources: CD player, tape deck, turntable to appropriate inputs.
4. Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block vents. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

1. Set speaker configuration: Choose large/small speakers and distance.
2. Program radio stations: Use auto-scan or manual tuning for AM/FM.
3. Adjust audio levels: Set individual channel volumes for surround sound.
4. Configure inputs: Assign appropriate source names if available.

CAUTION! Ensure all connections are secure before powering on.

Specifications

• Power Output: 100W x 2 (front), 30W x 2 (rear), 30W (center)
• Total Harmonic Distortion: 0.08%
• Frequency Response: 10Hz - 50kHz
• Signal-to-Noise Ratio: 85dB (Phono)
• Tuner Section: AM/FM stereo
• Preset Stations: 30 (20 FM, 10 AM)
• Input Sensitivity: Phono: 2.5mV, CD: 200mV
• Power Requirements: 120V AC, 60Hz
• Dimensions: 17-1/8" W x 5-7/8" H x 14-1/4" D

Controls and Settings

Front Panel: Power switch, Input selector, Volume control, Tone controls, Headphone jack.

Remote: Power, Input selection, Volume, Mute, Tuner controls, Surround mode selection.

Audio: Bass, Treble, Balance, Loudness. Surround: Dolby Pro Logic modes, Delay settings, Channel levels. Tuner: Manual/Auto tuning, Preset memory. System: Speaker setup, Input configuration.

Connecting Devices

Audio Sources: CD player, Tape deck, Turntable, Video sources. Speakers: Front L/R, Center, Rear L/R.

1. Turn off receiver before connecting devices.
2. Use appropriate cables (RCA for audio, speaker wire for speakers).
3. Connect turntable to Phono input only.
4. Select input via front panel or remote control.

Tip: Keep audio cables away from power cords to reduce interference.

Audio Settings

Dolby Pro Logic surround sound with adjustable parameters.

1. Surround Mode: Select Dolby Pro Logic for movie content.
2. Channel Levels: Adjust front, center, and rear speaker volumes.
3. Delay Settings: Set appropriate delay for rear speakers.
4. Tone Controls: Adjust bass and treble to preference.
5. Loudness: Engage for better low-volume listening.

WARNING! Do not exceed maximum power ratings for speakers.

Tuner Operation

AM/FM stereo tuner with 30 station presets.

1. Tuning: Use manual tuning buttons or auto-scan.
2. Preset Memory: Store favorite stations in memory.
3. Stereo/Mono: Select for weak FM signals.
4. Signal Strength: Monitor for optimal reception.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; avoid liquids.

CAUTION! Keep away from moisture and extreme temperatures. Ensure proper ventilation.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. Copyright © Kenwood Corporation. For support, contact Kenwood customer service or visit authorized service centers.

Troubleshooting

Reset: Disconnect power for 30 seconds to reset microprocessor.

Service: Contact authorized Kenwood service center for repairs.