Kenwood KR V7050 Manual

The Kenwood KR V7050 is a high-performance stereo receiver featuring Dolby Pro Logic surround sound, multiple audio inputs, AM/FM tuner with 30 station presets, remote control, tone controls, speaker A/B switching, and headphone output. Powered by 120V AC, 60Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Stereo receiver with Dolby Pro Logic, Remote Control, AM/FM antenna terminals, multiple audio inputs, speaker outputs, headphone jack.

Installation

Unpack and inspect contents. Place on stable surface.

1. Connect speakers: Attach speaker wires to appropriate terminals (A or B).
2. Connect antenna: Attach AM loop antenna and FM wire antenna to rear terminals.
3. Connect audio sources: Use appropriate input jacks for CD player, tape deck, etc.
4. Plug into AC power.

WARNING! Ensure proper ventilation; do not block rear vents. Ensure all connections are secure.

First-Time Setup

Power on receiver; follow initial setup procedure.

1. Program radio stations: Use auto-scan or manual tuning to set presets.
2. Set speaker configuration: Choose A, B, or A+B speaker output.
3. Adjust tone controls: Set bass and treble to personal preference.
4. Configure surround sound: Set Dolby Pro Logic mode if using surround speakers.

CAUTION! Ensure proper speaker impedance matching to prevent damage.

Specifications

• Power Output: 100 watts per channel (8 ohms).
• Tuner Section: AM/FM with 30 station presets.
• Sound: Dolby Pro Logic surround sound.
• Inputs: CD, Tape, Video/Aux, Phono.
• Outputs: Speaker A/B, Tape out, Headphone.
• Tone Controls: Bass ±10dB, Treble ±10dB.
• Power Source: 120V AC, 60Hz.
• Dimensions: Standard component width (17 inches).

Controls and Settings

Front Panel: POWER, INPUT SELECTOR, VOLUME, BASS, TREBLE, SPEAKER A/B.

Remote: POWER, Numeric buttons, INPUT SELECT, VOLUME, MUTE, TUNER PRESETS.

Audio: BASS, TREBLE, BALANCE, LOUDNESS. Speaker: A/B selection. Tuner: PRESET MEMORY, AUTO SCAN, MANUAL TUNING. Surround: DOLBY PRO LOGIC mode selection.

Connecting Devices

Audio Sources: CD, Tape, Video/Aux inputs. Speakers: A/B outputs.

1. Turn off receiver before connecting devices.
2. Match cables to appropriate input jacks.
3. Select input via INPUT SELECTOR (CD, TAPE, VIDEO/AUX, PHONO).
4. Connect speakers ensuring proper polarity.

Tip: Use high-quality cables for best audio performance.

Audio Settings

Supports multiple audio sources and surround sound processing.

1. Input selection: Choose appropriate source (CD, Tape, etc.).
2. Volume adjustment: Use volume knob or remote control.
3. Tone controls: Adjust bass and treble to preference.
4. Balance control: Adjust left/right speaker balance.
5. Loudness: Engage for enhanced bass at low volumes.
6. Dolby Pro Logic: Activate for surround sound with appropriate speakers.
7. Speaker selection: Choose A, B, or A+B outputs.

WARNING! Do not operate at maximum volume for extended periods.

Tuner Operation

AM/FM tuner with 30 presets and auto-scan functionality.

1. Tuning: Use manual tuning buttons or auto-scan.
2. Preset memory: Store favorite stations in memory locations.
3. FM stereo: Automatic stereo/mono switching.
4. AM tuning: Use built-in AM antenna or external antenna.

Care & Cleaning

Unplug before cleaning. Use dry cloth only; no liquids or aerosols.

CAUTION! Do not spray liquids; keep away from heat and moisture.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized service centers.

Troubleshooting

Reset: Disconnect power for 30 seconds if available.

Service: Contact authorized Kenwood service center.