Kenwood KR-V7060 Manual

The Kenwood KR-V7060 is a high-performance audio/video receiver featuring Dolby Pro Logic surround sound, multiple audio/video inputs, digital tuning with 30 presets, 100W per channel power output, remote control, and comprehensive connectivity options. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Audio/Video Operation 8. Special Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Dolby Pro Logic decoder, digital tuner, multiple A/V inputs, remote control, front panel controls, speaker terminals.

Feature	Description
Power Output	100W per channel (front), 30W (center), 30W (rear)
Dolby Pro Logic	Surround sound decoding
Tuner Presets	30 AM/FM stations
Audio Inputs	CD, Tape, Phono, Video/Aux
Video Inputs	2 composite video inputs
Speaker Terminals	Front, Center, Rear outputs
Remote Control	Full-function infrared remote
Headphone Jack	Front panel 3.5mm stereo
Tone Controls	Bass, Treble adjustment
Power Supply	120V AC, 60Hz

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

Connect speakers: Match polarity (+/-) for front, center, and rear speakers.
Connect audio sources: Use appropriate inputs (CD, Tape, Phono, Video/Aux).
Connect video sources: Use composite video inputs for VCR, DVD players.
Connect antenna: AM loop and FM wire antennas included.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initialization procedure.

Set speaker configuration: Small/Large for each channel in setup menu.
Program tuner presets: Auto-scan or manual tuning for AM/FM stations.
Set input levels: Adjust volume balance between sources.
Configure surround sound: Dolby Pro Logic mode settings.
Test all inputs and outputs.

CAUTION! Disconnect power before making any connections. Handle with care.

Specifications

Power Output: 100W x 2 (front), 30W (center), 30W (rear)
Total Harmonic Distortion: 0.08%
Frequency Response: 20Hz - 20kHz
Signal-to-Noise Ratio: 85dB
Tuner Section: AM/FM stereo with 30 presets
Input Sensitivity: Phono: 2.5mV, Line: 150mV
Surround System: Dolby Pro Logic
Power Requirements: 120V AC, 60Hz, 280W
Dimensions: 17-1/8" W x 5-7/8" H x 14-3/4" D
Weight: 20.3 lbs

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECTOR, TONE CONTROLS, HEADPHONE JACK.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, TUNER PRESETS, SURROUND MODE, TONE CONTROLS.

Audio: Bass, Treble, Balance, Loudness. Surround: Dolby Pro Logic modes (Normal, Wide, Phantom). Tuner: Auto/manual tuning, preset memory. System: Speaker size, input level, initialization.

Connecting Devices

Audio: CD player to CD input, tape deck to TAPE, turntable to PHONO. Video: VCR/DVD to VIDEO inputs.

Turn off receiver and components before connecting.
Use quality RCA cables for audio/video connections.
Connect turntable ground wire to ground terminal.
Select appropriate input source on front panel or remote.

Tip: Keep cable runs as short as possible for best signal quality.

Audio/Video Operation

Supports multiple audio sources and Dolby Pro Logic surround.

Select input: Choose CD, TAPE, PHONO, or VIDEO input.
Adjust volume: Use VOLUME control on front panel or remote.
Select surround mode: Choose Dolby Pro Logic mode for movies.
Tuner operation: Select AM/FM, tune stations, store presets.
Tape monitoring: Use for recording and playback monitoring.

WARNING! Do not exceed maximum volume levels to prevent speaker damage.

Special Features

Dolby Pro Logic: Creates surround sound from stereo sources. Tone Memory: Stores custom tone settings. Sleep Timer: Automatic shut-off. Headphone Output: Private listening.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; avoid chemicals. Keep away from moisture and extreme temperatures.

CAUTION! Do not use liquid cleaners; ensure proper ventilation during operation.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power cord connection; test outlet; check fuse.
No sound	Speaker connections/mute	Check speaker wires; ensure not muted; verify input selection.
Poor FM reception	Antenna placement	Extend FM antenna; reposition for better reception.
Remote not working	Batteries/obstructions	Replace batteries; ensure line of sight to IR sensor.
Hum or noise	Grounding/cables	Check turntable ground; use shielded cables; separate from power cords.

Reset: Disconnect power for 30 seconds to reset microprocessor.

Service: Contact authorized Kenwood service center for repairs.