Kenwood KR-X1000 Manual

The Kenwood KR-X1000 is a high-performance stereo receiver featuring AM/FM tuner, multiple audio inputs, phono input for turntables, tone controls, loudness compensation, speaker outputs, headphone jack, and remote control capability. With 100 watts per channel power output, this receiver delivers exceptional audio quality for home entertainment systems. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Radio Operation 8. Audio Settings 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Stereo receiver with AM/FM tuner, Remote Control, Multiple audio inputs, Phono input, Speaker terminals, Headphone jack.

Feature	Description
Power Output	100 watts per channel (8 ohms)
Tuner	AM/FM with 30 station presets
Audio Inputs	CD, Tape, Aux, Phono
Phono Input	For turntable connection (MM cartridge)
Speaker Outputs	A/B speaker selection
Headphone Jack	For private listening
Tone Controls	Bass, Treble, Balance
Loudness	Compensation for low-volume listening
Remote Control	Included for full operation
Power	Turns receiver on/off

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

Connect speakers: Use speaker wire to connect to A/B speaker terminals.
Connect audio sources: Use appropriate cables for CD player, tape deck, turntable.
Connect antenna: Attach AM loop antenna and FM wire antenna.
Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block ventilation openings. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

Set speaker configuration: Select A, B, or A+B speakers.
Tune radio stations: Use auto-scan to preset AM/FM stations.
Adjust audio settings: Set bass, treble, balance to preference.
Configure inputs: Select appropriate input for each connected device.

CAUTION! Ensure all connections are secure before powering on.

Specifications

Power Output: 100W + 100W (8 ohms, 20Hz-20kHz)
Total Harmonic Distortion: 0.08%
Frequency Response: 10Hz-100kHz
Input Sensitivity: Phono: 2.5mV, Line: 150mV
Signal-to-Noise Ratio: Phono: 80dB, Line: 100dB
Tuner Section: FM/AM with 30 presets
Inputs: Phono, CD, Tape, Aux
Outputs: Speakers, Headphone, Tape Rec
Power Requirements: 120V AC, 60Hz
Dimensions: 17-1/8" W x 5-7/8" H x 14-3/4" D

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECTOR, BASS, TREBLE, BALANCE, LOUDNESS, SPEAKERS A/B.

Remote: POWER, VOLUME, MUTE, INPUT SELECTION, TUNER PRESETS, TONE CONTROLS.

Audio Controls: Bass (±10dB at 100Hz), Treble (±10dB at 10kHz), Balance (L/R adjustment), Loudness (on/off). Input Selection: Phono, CD, Tape, Aux. Speaker Selection: A, B, A+B. Tuner: Manual tuning, Auto-scan, Preset memory.

Connecting Devices

Audio Sources: Phono for turntables, CD for CD players, Tape for tape decks, Aux for other devices.

Turn off receiver before connecting devices.
Match cables to correct input jacks.
Ensure proper grounding for phono input.
Select appropriate input source on front panel.

Tip: Use high-quality cables for best audio performance.

Radio Operation

AM/FM tuner with 30 station presets.

Select tuner input: Press TUNER on front panel or remote.
Tune stations: Use manual tuning or auto-scan.
Store presets: Tune to desired station, press and hold preset button.
Recall presets: Press numbered preset buttons.
Mono/stereo: Auto-switching for FM stereo reception.

WARNING! Ensure proper antenna connection for best reception.

Audio Settings

Tone Controls: Adjust bass and treble to preference. Balance: Adjust left/right channel balance. Loudness: Compensates for Fletcher-Munson curves at low volumes.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth only; avoid liquids. Keep unit dry and well-ventilated.

CAUTION! Do not use chemical cleaners; avoid moisture and extreme temperatures.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Kenwood Corporation. All trademarks property of their respective owners. For support, visit www.kenwood.com or contact authorized service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power connection; ensure outlet is working.
No sound	Speaker connections/volume	Check speaker wires; ensure volume is up; verify input selection.
Poor radio reception	Antenna placement	Reposition antennas; ensure proper connection.
Distorted sound	Input level/speakers	Reduce volume; check speaker impedance compatibility.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear path to IR sensor.

Reset: Disconnect power for 30 seconds to reset microprocessor.

Service: Contact authorized Kenwood service center for repairs.