Kenwood NX 5300 Manual

The Kenwood NX 5300 is a professional digital two-way radio designed for commercial and industrial use. This VHF/UHF portable radio features digital/analog operation, IP67 waterproof rating, large LCD display, programmable buttons, built-in Bluetooth, GPS capability, and robust construction for demanding environments. Below are key sections covering safety, features, installation, programming, operation, and troubleshooting.

1. Features at a Glance 2. Installation and Setup 3. Basic Operation 4. Specifications 5. Controls and Functions 6. Programming and Configuration 7. Advanced Features 8. Maintenance and Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Digital/Analog operation, Large LCD display, Programmable buttons, Bluetooth connectivity, GPS capability, IP67 rating.

Feature	Description
Frequency Range	VHF: 136-174 MHz, UHF: 400-470 MHz
Digital Mode	NXDN® Digital and FM Analog
IP Rating	IP67 Submersible (1 meter for 30 minutes)
Display	Large LCD with backlight
Bluetooth	Built-in for wireless accessories
GPS	Built-in GPS receiver
Battery	High-capacity Li-ion battery
Channels	Up to 512 channels programmable
Audio Output	1W audio power
Programming	KPG-111D/112D Programming Software

Installation and Setup

Unpack and inspect contents. Install battery and antenna.

Battery Installation: Align battery with radio contacts, slide until it clicks.
Antenna Installation: Screw antenna clockwise until secure.
Charging: Place radio in charger; ensure charging indicator lights.
Initial Power On: Press and hold POWER button to turn on.

WARNING! Use only Kenwood-approved batteries and chargers. Do not expose to extreme temperatures.

Basic Operation

Power on radio; select channel and communicate.

Power On/Off: Press and hold POWER button.
Channel Selection: Rotate CHANNEL selector knob.
Transmit: Press and hold PTT (Push-To-Talk) button.
Volume Control: Rotate VOLUME knob.
Monitor: Press MONI button to monitor channel activity.
Scan: Press SCAN button to enable channel scanning.

CAUTION! Ensure proper antenna is attached before transmitting.

Specifications

Frequency Range: VHF 136-174 MHz, UHF 400-470 MHz
Output Power: VHF: 5W, UHF: 4W (programmable)
Modulation: 16KΦF3E (Digital), 11KΦF3E (Analog)
Battery Life: Up to 12 hours (typical use)
Operating Temp: -30°C to +60°C
Dimensions: 58(W) x 130(H) x 37.5(D) mm
Weight: Approx. 350g (with battery)
Channels: Up to 512 programmable channels
IP Rating: IP67 Dust and Waterproof

Controls and Functions

Front Panel: POWER/VOLUME knob, CHANNEL selector, PTT button, PROGRAMMABLE buttons, LCD display.

Top Panel: Antenna connector, On/Off/Volume knob, Channel selector.

Side Buttons: PTT (left side), PROGRAMMABLE buttons (user-defined). Display: Shows channel, mode, battery status, signal strength. Programming: Buttons can be programmed for functions like SCAN, MONITOR, EMERGENCY, LOCK.

Programming and Configuration

Use KPG-111D/112D software for programming.

Connect radio to PC using programming cable.
Launch KPG-111D/112D programming software.
Read data from radio or create new configuration.
Program frequencies, channels, and functions.
Write configuration to radio.

Tip: Backup current configuration before making changes.

Advanced Features

Digital Operation: NXDN® digital mode for clear audio and enhanced features. GPS: Location tracking and reporting. Bluetooth: Wireless headset connectivity. Emergency: Emergency call function. Scan: Priority channel scanning. DTMF: DTMF encoding and decoding.

Maintenance and Care

Clean with soft, dry cloth. Avoid chemicals and abrasives.

CAUTION! Do not immerse in water beyond IP67 specifications. Use only approved accessories.

Regulatory Information

FCC Part 90: Certified for land mobile radio service. IC RSS-119: Complies with Canadian requirements. This device complies with Part 15 of FCC Rules. For support, visit www.kenwood.com/usa or contact authorized Kenwood dealer.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Battery/connections	Check battery installation; charge battery; check power button.
No transmission	PTT/antenna	Ensure PTT fully pressed; check antenna connection.
Poor reception	Antenna/location	Check antenna; move to better location; check squelch setting.
No audio	Volume/speaker	Adjust volume; check speaker; ensure not in mute mode.
Programming failure	Cable/software	Check programming cable; verify software version; restart process.

Reset: Consult programming software for reset options.

Service: Contact authorized Kenwood service center.