Kenwood TK 2000 Manual

The Kenwood TK 2000 is a professional VHF two-way radio designed for commercial and industrial use. This rugged radio features 16 channels, 5W output power, programmable functions, built-in CTCSS/DCS, wide frequency range, and durable construction suitable for demanding environments. Below are key sections covering safety, features, installation, programming, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Programming the Radio 7. Operation 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Durable chassis, 16-channel capacity, programmable buttons, LCD display, antenna connector, speaker/microphone, battery pack, and charging contacts.

Feature	Description
Frequency Range	VHF 136-174 MHz
Output Power	5W (High), 1W (Low)
Channels	16 programmable channels
CTCSS/DCS	Built-in encode/decode
Battery	Ni-Cd or Ni-MH battery pack
Display	LCD with channel and status indicators
Programmable Buttons	Mon/T-Call, LAMP, SCAN, etc.
Antenna Connector	BNC type
Operating Temp	-30°C to +60°C
Dimensions	58W x 130H x 37D mm

Installation

Unpack and inspect contents. Install battery and antenna.

Install battery: Align battery contacts, slide until it clicks into place.
Attach antenna: Screw BNC antenna connector clockwise until secure.
Charge battery: Place radio in charger until indicator shows full charge.
Attach belt clip: Secure to back of radio for portable use.

WARNING! Use only Kenwood-approved batteries and accessories. Do not operate while charging.

First-Time Setup

Power on radio; verify basic operation.

Turn on: Rotate volume knob clockwise; confirm display illuminates.
Select channel: Use channel selector knob to choose channel 1.
Adjust volume: Set to comfortable listening level.
Test transmission: Press PTT button; speak into microphone.
Monitor squelch: Adjust squelch control to eliminate background noise.

CAUTION! Ensure proper antenna is installed before transmitting.

Specifications

Frequency Range: VHF 136-174 MHz
Channel Capacity: 16 channels
Output Power: 5W (High), 1W (Low) selectable
Modulation: 16KΦF3E (FM)
Power Supply: 7.2V DC (battery pack)
Battery Life: Approx. 8 hours (5-5-90 duty cycle)
Dimensions: 58W x 130H x 37D mm (with standard battery)
Weight: Approx. 350g (with standard battery)
Operating Temp: -30°C to +60°C
CTCSS: 50 tones standard
DCS: 104 codes standard

Controls and Settings

Front Panel: Volume control, Channel selector, Power/Volume knob, PTT button, Programmable buttons.

Programmable Functions: MONITOR, T-CALL, LAMP, SCAN, L/O, TONE, DCS, REPT, SQL.OFF, DTSS.SEL, DTMF.M, 2TONE, 5TONE, ANI, PAGER, COMPANDER, BCL, TOT, BEEP, SAVE, VOX, RTE, RESET, OPTION.

Display Indicators: Channel number, Busy indicator, TX/RX indicator, Battery level, CTCSS/DCS status, Scan status.

Programming the Radio

Requires KPG-46D programming software and cable.

Install programming software on Windows PC.
Connect programming cable to radio and PC.
Read current data from radio.
Program frequencies, CTCSS/DCS, power settings per channel.
Assign functions to programmable buttons.
Write data to radio and verify operation.

Tip: Backup current programming before making changes.

Operation

Basic radio operation procedures.

Power on: Rotate volume knob clockwise.
Select channel: Turn channel selector knob.
Adjust volume: Set appropriate listening level.
Transmit: Press and hold PTT button; speak clearly into microphone.
Receive: Release PTT button; listen for response.
Monitor: Press MONITOR button to open squelch.
Scan: Press SCAN button to enable channel scanning.
Backlight: Press LAMP button to illuminate display.

WARNING! Transmit only on authorized frequencies with proper license.

Maintenance

Regular maintenance ensures optimal performance.

Clean exterior: Use soft, dry cloth; avoid solvents.
Battery care: Charge fully before first use; avoid complete discharge.
Antenna inspection: Check for damage; replace if bent or cracked.
Connector check: Ensure clean, secure connections.
Storage: Store in cool, dry place when not in use.

CAUTION! Do not disassemble radio; refer service to qualified technicians.

Regulatory Information

FCC Part 90: This device complies with Part 90 of the FCC rules for land mobile radio services. Operation is subject to licensing by the FCC. This radio generates RF energy; maintain proper distance during operation. Copyright © Kenwood Corporation. For support, contact authorized Kenwood dealer or visit www.kenwood.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Battery depleted/improperly installed	Charge battery; ensure proper installation.
No transmission	PTT button/antenna	Check PTT operation; ensure antenna is properly connected.
Poor reception	Antenna/squelch setting	Check antenna connection; adjust squelch control.
No audio	Volume setting/speaker	Increase volume; check speaker operation.
Display blank	Power/battery	Check power connection; verify battery charge.
Cannot program	Cable/software	Verify programming cable connection; check software compatibility.

Reset: Use programming software to reset to factory defaults if needed.

Service: Contact authorized Kenwood service center for repairs.