Kenwood TK 2207 Manual

The Kenwood TK 2207 is a professional VHF two-way portable radio designed for commercial and industrial use. This compact and durable radio features 16 channels, 5W output power, robust construction meeting MIL-STD 810 C/D/E standards, programmable functions, built-in scrambler capability, and multiple signaling options. Below are key sections covering safety, features, installation, programming, operation, and troubleshooting.

Features at a Glance

Key components: Durable housing, LCD display, programmable buttons, antenna, battery pack, speaker/microphone, charging contacts.

Feature	Description
Frequency Range	VHF 136-174 MHz
Channels	16 programmable channels
Output Power	5W (High), 1W (Low) selectable
Battery	7.4V 1500mAh Li-ion standard
Display	LCD with channel, battery, transmit indicators
Programming	KPG-22D/KPG-36D programming software
Scanning	Programmable scan with priority
Signaling	2-tone, 5-tone, DTMF capabilities
Construction	MIL-STD 810 C/D/E compliant
Dimensions	58W x 130H x 37D mm (with standard battery)

Installation

Unpack and inspect contents. Install battery and antenna.

1. Install battery: Align battery contacts, slide battery upward until it clicks.
2. Install antenna: Screw antenna clockwise onto antenna connector.
3. Charge battery: Place radio in charger; charge for 6-8 hours initially.
4. Attach accessories: Connect belt clip, speaker mic if required.

WARNING! Do not transmit without antenna attached. Ensure battery is properly installed.

First-Time Setup

Power on radio; verify basic operation.

1. Turn on: Rotate volume knob clockwise; check for power-up beep.
2. Select channel: Use channel selector knob to choose desired channel.
3. Adjust volume: Set appropriate listening level.
4. Test transmission: Press PTT button; speak into microphone.
5. Monitor squelch: Adjust squelch control to eliminate background noise.

CAUTION! Ensure radio is programmed for your frequency requirements before use.

Specifications

• Frequency Range: VHF 136-174 MHz
• Channels: 16 programmable
• Output Power: 5W (High), 1W (Low)
• Modulation: 16KΦF3E (FM)
• Battery Life: Approx. 10 hours (5-5-90 duty cycle)
• Operating Temp: -30°C to +60°C
• Weight: 450g (with standard battery)
• Antenna Impedance: 50Ω
• Audio Output: 500mW at 8Ω
• Programming Interface: KPG-22D/KPG-36D programming cable

Controls and Settings

Front Panel: Volume control, channel selector, PTT button, programmable buttons.

Top Controls: Power/volume knob, channel selector, programmable side buttons.

Display Indicators: Channel number, battery level, transmit indicator, busy channel, scan status. Programmable Functions: Monitor, scan, power level, timeout timer, busy channel lockout, squelch levels.

Programming the Radio

Requires KPG-22D/KPG-36D programming software and cable.

1. Install programming software on Windows PC.
2. Connect programming cable to radio and PC.
3. Read current data from radio.
4. Program frequencies, tones, and functions as required.
5. Write data to radio and verify programming.

Tip: Always backup existing programming before making changes.

Operating Instructions

Basic radio operation procedures.

1. Power on: Rotate volume knob clockwise.
2. Select channel: Turn channel selector knob.
3. Transmit: Press and hold PTT button; speak clearly into microphone.
4. Receive: Release PTT button; listen for response.
5. Adjust volume: Set for comfortable listening level.
6. Monitor: Use monitor button to open squelch if needed.
7. Scan: Activate scan function to monitor multiple channels.

WARNING! Transmit only when necessary and keep transmissions brief.

Battery Information

Standard battery: 7.4V 1500mAh Li-ion. Charging time: 6-8 hours.

Battery Care: Charge fully before first use. Avoid complete discharge. Store in cool, dry place. Replace when capacity diminishes.

Care & Maintenance

Clean with soft, dry cloth. Avoid solvents and chemicals.

CAUTION! Do not immerse in water. Keep away from extreme temperatures and humidity.

Regulatory Information

FCC Part 90 certified for land mobile radio service. This device complies with part 15 of the FCC Rules. Operation is subject to license requirements. Copyright © Kenwood Corporation. For support, contact authorized Kenwood dealer or visit www.kenwood.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Battery dead/not installed	Charge battery; ensure proper installation.
No transmission	PTT button/antenna	Check PTT operation; ensure antenna attached.
Poor reception	Antenna/squelch setting	Check antenna connection; adjust squelch.
No audio	Volume setting/speaker	Increase volume; check speaker operation.
Programming failure	Cable/software	Check cable connection; verify software compatibility.

Reset: Requires programming software for full reset.

Service: Contact authorized Kenwood service center.