Kenwood TK 3200L Manual

The Kenwood TK 3200L is a professional VHF two-way radio designed for commercial and industrial use. This rugged portable radio offers 16 channels, 5W output power, MIL-STD 810 C/D compliance for durability, programmable functions, and reliable communication performance. Below are key sections covering features, installation, operation, programming, and troubleshooting.

Features at a Glance

Key components: Durable housing, LCD display, programmable buttons, antenna, battery pack, and charging contacts.

Installation

Unpack and inspect contents. Install battery and antenna properly.

1. Battery installation: Align battery contacts, slide battery upward until it clicks into place.
2. Antenna installation: Screw antenna clockwise onto antenna connector until snug.
3. Belt clip: Attach belt clip to rear of radio if required.
4. Charging: Place radio in charger with power contacts aligned.

WARNING! Do not operate radio while charging. Ensure antenna is properly installed before transmitting.

First-Time Setup

Charge battery fully before first use. Program channels as required.

1. Power on: Rotate volume knob clockwise to turn on radio.
2. Channel selection: Use channel selector knob to choose desired channel.
3. Volume adjustment: Rotate volume knob to set audio level.
4. Squelch adjustment: Use programming software to set squelch levels.
5. Power level: Select high (5W) or low (1W) power as needed.

CAUTION! Radio must be programmed before use. Contact authorized dealer for programming.

Specifications

• Frequency Range: VHF 136-174 MHz
• Channels: 16 programmable
• Output Power: 5W (High), 1W (Low)
• Modulation: 16KΦF3E (FM)
• Battery Life: Approx. 10 hours (5-5-90 duty cycle)
• Operating Temp: -30°C to +60°C
• Humidity: 5% to 95% relative humidity
• Shock/Vibration: MIL-STD 810 C/D compliant
• Audio Output: 500mW at 10% distortion
• Dimensions: 58W x 130H x 37D mm

Controls and Settings

Front Panel: Volume control, channel selector, PTT button, programmable buttons.

Display Indicators: Channel number, battery level, transmit indicator, busy channel indicator.

Programmable Functions: Monitor button, scan functions, power level selection, timeout timer, busy channel lockout. All functions programmable via KPG-56D software.

Programming

Requires KPG-56D programming software and programming cable.

1. Install KPG-56D software on Windows PC.
2. Connect programming cable to radio and PC.
3. Read current data from radio.
4. Program frequencies, CTCSS/DCS, power levels, and functions.
5. Write data to radio and verify programming.

Tip: Always backup current programming before making changes.

Operation

Basic radio operation procedures.

1. Power on: Rotate volume knob clockwise.
2. Select channel: Turn channel selector knob.
3. Adjust volume: Rotate volume knob to comfortable level.
4. Transmit: Press and hold PTT button, speak clearly into microphone.
5. Receive: Release PTT button to listen.
6. Monitor: Press monitor button to temporarily open squelch.
7. Scan: Press scan button if programmed (activates channel scanning).

WARNING! Only transmit on authorized frequencies with proper license.

Maintenance

Regular maintenance ensures optimal performance.

1. Cleaning: Use soft cloth with mild detergent. Do not use solvents.
2. Battery care: Charge battery fully before first use. Avoid complete discharge.
3. Antenna inspection: Check antenna regularly for damage.
4. Connectors: Keep connectors clean and free from debris.

CAUTION! Use only Kenwood-approved accessories and batteries.

Regulatory Information

FCC Part 90 certified for land mobile radio service. This device complies with Part 15 of FCC Rules. Operation subject to condition that device does not cause harmful interference. Changes not approved by Kenwood may void user's authority to operate equipment. For technical support, contact authorized Kenwood dealer.

Troubleshooting

Reset: Requires reprogramming via KPG-56D software.

Service: Contact authorized Kenwood service center for repairs.