kenwood tk 3202l manual

The Kenwood TK-3202L is a professional VHF two-way portable radio designed for commercial and industrial use. This rugged radio features 16 channels, 5W output power, MIL-STD 810 C/D compliance for durability, programmable functions, built-in voice scrambler, and multiple signaling options. Below are key sections covering features, installation, operation, programming, and troubleshooting.

Features at a Glance

Key components: Durable chassis, LCD display, programmable buttons, antenna, battery pack, charging contacts.

Installation

Unpack and inspect contents. Install battery and antenna.

1. Battery installation: Align battery contacts, slide battery upward until it clicks.
2. Antenna installation: Screw antenna clockwise onto antenna connector.
3. Belt clip: Attach to rear of radio if required.
4. Charging: Place radio in charging cradle, ensure charging indicator lights.

WARNING! Use only Kenwood-approved batteries and accessories. Do not force components during installation.

First-Time Setup

Power on radio; initialize settings.

1. Charge battery: Place in charger until full (approx. 3 hours).
2. Power on: Rotate volume knob clockwise.
3. Select channel: Use channel selector knob.
4. Adjust volume: Rotate volume knob to desired level.
5. Squelch setting: Adjust squelch level via programming software.

CAUTION! Ensure battery is fully charged before first use. Use proper charging equipment.

Specifications

• Frequency Range: VHF 136-174 MHz
• Channels: 16 programmable
• Output Power: 5W (High), 1W (Low)
• Battery Life: Approx. 10 hours (5-5-90 duty cycle)
• Operating Temp: -30°C to +60°C
• Weight: 450g (with battery)
• IP Rating: IP54 dust and water resistant
• Modulation: 16KΦF3E / 11KΦF3E
• Audio Output: 500mW at 8Ω

Controls and Settings

Front Panel: Volume knob, channel selector, PTT button, display. Side Buttons: Programmable functions (monitor, scan, power level, etc.)

Display Indicators: Channel number, battery level, transmit indicator, busy channel, programmable function status.

Basic Functions: Power on/off (volume knob), channel selection (selector knob), transmit (PTT button), monitor (side button), scan (programmable function). Audio Settings: Volume control, squelch levels, tone settings via programming.

Programming

Requires KPG-89D programming software and programming cable.

1. Install programming software on PC.
2. Connect radio to PC using programming cable.
3. Read current data from radio.
4. Program frequencies, tones, functions as required.
5. Write data to radio and verify.

Tip: Backup current programming before making changes. Use licensed frequencies only.

Operation

Basic radio operation procedures.

1. Power on: Rotate volume knob clockwise.
2. Select channel: Turn channel selector knob.
3. Adjust volume: Rotate volume knob to comfortable level.
4. Transmit: Press and hold PTT button, speak clearly into microphone.
5. Receive: Release PTT button to listen.
6. Monitor: Press monitor button to temporarily open squelch.
7. Scan: Enable scan function via programmable button.

WARNING! Transmit only on authorized frequencies. Maintain proper radio etiquette.

Maintenance

Regular maintenance ensures optimal performance.

Clean exterior with soft, dry cloth. Check antenna for damage. Inspect battery contacts. Store in dry, cool place. Avoid extreme temperatures and moisture.

CAUTION! Do not use chemicals or solvents for cleaning. Do not immerse in water.

Regulatory Information

FCC Part 90 certified for land mobile radio service. This device complies with Part 15 of FCC rules. Operation subject to condition that device does not cause harmful interference. Copyright © Kenwood Corporation. For support, contact authorized Kenwood dealer or visit www.kenwood.com.

Troubleshooting

Reset: Requires programming software for full reset.

Service: Contact authorized Kenwood service center for repairs.