Kenwood TK 3230 Manual

The Kenwood TK 3230 is a professional two-way portable radio designed for business and commercial use. This VHF/UHF radio features robust construction, multiple channel capability, programmable functions, and reliable communication performance. Below are key sections covering features, installation, operation, programming, maintenance, and troubleshooting.

Features at a Glance

Key components: Durable housing, LCD display, programmable buttons, antenna, battery pack, and charging contacts.

Installation and Setup

Unpack and inspect contents. Install battery and antenna before first use.

1. Battery installation: Align battery contacts and slide battery onto radio until it clicks into place.
2. Antenna installation: Screw antenna clockwise onto antenna connector until snug.
3. Charging: Place radio in charging cradle; ensure charging indicator lights up.
4. Initial power on: Turn volume knob clockwise to power on the radio.

WARNING! Use only Kenwood-approved batteries and chargers. Do not force connections.

Basic Operation

Power on radio; adjust volume and select channels as needed.

1. Power on/off: Turn volume knob clockwise to power on, counter-clockwise to power off.
2. Volume control: Rotate volume knob to adjust audio level.
3. Channel selection: Use channel selector knob or up/down buttons.
4. Transmit: Press and hold PTT (Push-to-Talk) button while speaking.
5. Receive: Release PTT button to listen to incoming transmissions.

CAUTION! Maintain proper radio etiquette and follow local communication regulations.

Specifications

• Frequency Range: VHF 136-174 MHz / UHF 400-470 MHz
• Channels: 128 max programmable channels
• Power Output: 5W (VHF), 4W (UHF)
• Battery Life: Up to 10 hours (standard use)
• Dimensions: 58(W) x 130(H) x 37(D) mm
• Weight: 350g (with battery)
• Operating Temp: -30°C to +60°C
• IP Rating: IP54/55 dust and water resistant
• Modulation: 16KΦF3E / 11KΦF3E

Controls and Functions

Front Panel: Volume knob, channel selector, PTT button, programmable buttons, LCD display.

Side Controls: Power on/off (volume knob), accessory connector, battery release.

Display Indicators: Channel number, battery level, transmit/receive status, scan mode. Programmable Functions: Monitor, scan, power level, tone squelch, VOX, emergency call. Audio: Volume control, built-in speaker, external speaker/mic capability.

Programming and Configuration

Requires KPG-89D programming software and programming cable.

1. Connect radio to PC using programming cable.
2. Launch KPG-89D software and read current configuration.
3. Program frequencies, tones, and functions as required.
4. Write configuration to radio and verify operation.

Tip: Backup current configuration before making changes. Only qualified personnel should program radios.

Battery and Charging

Standard Li-ion battery pack with charging cradle.

1. Charging: Place radio in charging cradle; charging indicator will light.
2. Battery life: Approximately 10 hours with standard battery.
3. Battery saving: Automatic power save mode extends battery life.
4. Battery replacement: Use only Kenwood-approved batteries.

WARNING! Do not charge damaged batteries. Use only approved chargers in well-ventilated areas.

Maintenance and Care

Regular cleaning and inspection ensure optimal performance.

1. Cleaning: Use soft, dry cloth; avoid liquids and solvents.
2. Antenna: Check for damage; replace if bent or cracked.
3. Battery contacts: Keep clean and free of corrosion.
4. Storage: Store in cool, dry place away from direct sunlight.

CAUTION! Do not disassemble radio; refer service to qualified technicians.

Regulatory Information

FCC Part 90: Certified for land mobile radio service. Complies with relevant industry standards. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized Kenwood service centers.

Troubleshooting

Reset: Programming software reset function if available.

Service: Contact authorized Kenwood service center for repairs.