Kenwood TK-3402U16P Manual

The Kenwood TK-3402U16P is a professional UHF two-way radio designed for business and commercial use. This 16-channel radio operates in the UHF frequency range with 5W output power, featuring robust construction, programmable channels, CTCSS/DCS capabilities, and multiple scanning functions. Below are key sections covering features, installation, programming, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. Basic Operation 4. Specifications 5. Controls and Functions 6. Programming 7. Advanced Features 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: UHF transceiver, LCD display, programmable buttons, antenna, battery pack, and belt clip.

FeatureDescription
Frequency RangeUHF 400-470MHz
Output Power5W (High), 1W (Low)
Channels16 programmable channels
CTCSS/DCS50 CTCSS tones, 105 DCS codes
ScanningProgrammable scan with priority
BatteryLi-ion 1500mAh (standard)
DisplayBacklit LCD with channel info
ProgrammingKPG-46D software required
Dimensions118mm x 55mm x 32mm
WeightApprox. 290g with battery

Installation

Unpack and inspect contents. Install battery and antenna.

  1. Battery installation: Align battery contacts, slide battery onto radio until it clicks.
  2. Antenna installation: Screw antenna clockwise into antenna connector.
  3. Belt clip: Attach to back of radio for portable use.
  4. Charging: Place radio in charging cradle; ensure charging indicator lights.

WARNING! Do not transmit without antenna attached. Ensure battery is properly installed.

Basic Operation

Power on radio; select channel and communicate.

  1. Power on: Rotate volume knob clockwise.
  2. Channel selection: Use channel selector knob or up/down buttons.
  3. Transmit: Press and hold PTT button; speak clearly into microphone.
  4. Receive: Release PTT to listen; adjust volume as needed.
  5. Monitor: Press MONI button to temporarily disable CTCSS/DCS.

CAUTION! Only transmit when necessary to conserve battery life.

Specifications

Controls and Functions

Front Panel: Volume knob, channel selector, PTT button, programmable buttons.

Top: Power/volume knob, channel selector. Side: PTT, programmable buttons (P1, P2, P3), accessory connector.

Display: Shows channel number, battery level, transmit indicator, CTCSS/DCS status. Buttons: MONI (monitor), SCAN (scan activation), LAMP (backlight).

Programming

Requires KPG-46D programming software and programming cable.

  1. Install KPG-46D software on Windows PC.
  2. Connect radio to PC using programming cable.
  3. Read current data from radio.
  4. Program frequencies, CTCSS/DCS, power levels for each channel.
  5. Write data to radio and verify programming.

Tip: Backup current programming before making changes.

Advanced Features

Scanning: Programmable scan with priority channel. Time-out Timer: Limits transmission time. Battery Save: Extends battery life. VOX: Voice-activated transmission. DTMF: Optional encoding capability.

Maintenance

Clean exterior with dry cloth. Check antenna and battery connections regularly.

CAUTION! Do not use chemicals or solvents. Keep away from moisture.

Regulatory Information

FCC Part 90 certified for land mobile radio service. Complies with relevant industry standards. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized Kenwood dealer.

Troubleshooting

SymptomPossible CauseCorrective Action
No powerBattery/connectionsCheck battery installation; charge battery; check power switch.
No transmissionPTT/antennaEnsure PTT fully pressed; check antenna connection.
Poor receptionAntenna/locationCheck antenna; move to better location; check squelch setting.
Battery drains quicklyBattery age/usageReplace battery; reduce transmission time; enable battery save.
No audioVolume/speakerAdjust volume; check speaker connection; reset radio.

Reset: Programming software reset option available.

Service: Contact authorized Kenwood service center.

Kenwood TK-3402U16P Manual © - All Rights Reserved 2025