Kenwood TK 360 Manual

The Kenwood TK 360 is a professional two-way radio designed for commercial and industrial use. This VHF/UHF portable radio features robust construction, multiple channel capability, programmable functions, and reliable communication performance. Below are key sections covering safety, features, installation, operation, programming, and troubleshooting.

Features at a Glance

Key components: Durable housing, LCD display, programmable buttons, antenna, battery pack, charging contacts.

Feature	Description
Frequency Range	VHF: 136-174 MHz / UHF: 400-470 MHz
Channels	Up to 128 programmable channels
Output Power	5W (VHF) / 4W (UHF)
LCD Display	Backlit display with channel and status information
Programmable Buttons	Multiple function buttons for custom operations
Battery Life	Up to 10 hours depending on usage
Scan Function	Programmable scan with priority channel
VOX Capability	Voice-activated transmission
Water Resistance	IP54 or IP55 rated for dust and water protection
Accessory Port	For external speaker microphones and headsets

Installation

Unpack and inspect contents. Install battery and antenna.

1. Battery Installation: Align battery contacts, slide battery onto radio until it clicks.
2. Antenna Installation: Screw antenna clockwise into antenna connector until snug.
3. Belt Clip: Attach belt clip to back of radio if required.
4. Charging: Place radio in charging cradle ensuring proper contact.

WARNING! Use only Kenwood-approved batteries and accessories. Do not force connections.

First-Time Setup

Charge battery fully before first use. Basic radio configuration.

1. Power On: Turn volume knob clockwise to power on radio.
2. Channel Selection: Use channel selector knob to choose desired channel.
3. Volume Adjustment: Rotate volume knob for desired audio level.
4. Squelch Setting: Adjust squelch control to minimize background noise.
5. Frequency Programming: Use programming software to set frequencies (requires PC connection).

CAUTION! Radio must be programmed for your specific frequency requirements before use.

Specifications

• Frequency Range: VHF 136-174 MHz / UHF 400-470 MHz
• Channels: 128 programmable channels
• Output Power: 5W (VHF) / 4W (UHF)
• Battery: 1500mAh Ni-MH or equivalent Li-ion
• Dimensions: Approximately 58(W) x 130(H) x 37(D) mm
• Weight: Approximately 350g with battery
• Operating Temp: -30°C to +60°C
• IP Rating: IP54/IP55 dust and water resistant
• Modulation: 16KΦF3E / 11KΦF3E
• Antenna Impedance: 50Ω

Controls and Settings

Front Panel: Power/Volume knob, Channel selector, PTT button, Programmable buttons, LCD display.

Button Functions: PTT (Push-to-Talk), MONI (Monitor), SCAN, LAMP (Backlight), Function key combinations.

Display Indicators: Channel number, Battery level, Transmit indicator, Scan status, CTCSS/DCS codes. Audio: Volume control, Squelch levels, Tone settings. Programming: Channel frequencies, CTCSS/DCS codes, Power levels, Scan lists, Time-out timer.

Programming the Radio

Requires KPG-36D/KPG-46D programming software and programming cable.

1. Install programming software on Windows PC.
2. Connect radio to PC using programming cable.
3. Read current data from radio.
4. Program frequencies, tones, and functions as required.
5. Write data to radio and verify programming.

Tip: Always backup current programming before making changes.

Operation

Basic radio operation procedures.

1. Transmitting: Press and hold PTT button, speak clearly into microphone.
2. Receiving: Release PTT button to listen; adjust volume as needed.
3. Channel Changing: Rotate channel selector knob to desired channel.
4. Scan Operation: Press SCAN button to start/stop scanning programmed channels.
5. Monitor Function: Press MONI to listen to weak signals or open squelch.
6. Backlight: Press LAMP button to illuminate display (varies by programming).

WARNING! Only transmit on authorized frequencies with proper licensing.

Battery Information

Battery charging and maintenance guidelines.

• Initial Charge: Charge battery for recommended time before first use
• Regular Charging: Use only Kenwood-approved chargers
• Battery Life: Typical 8-10 hours depending on transmit/receive ratio
• Storage: Store in cool, dry place when not in use
• Replacement: Replace battery when performance decreases significantly

CAUTION! Do not expose batteries to extreme temperatures or short circuit.

Care & Maintenance

Regular cleaning and inspection procedures.

1. Cleaning: Use soft, dry cloth; mild detergent if necessary
2. Antenna: Check for damage; replace if bent or broken
3. Battery Contacts: Keep clean and free of corrosion
4. Housing: Inspect for cracks or damage
5. Accessories: Check connectors and cables for wear

CAUTION! Do not use solvents or abrasive cleaners.

Regulatory Information

FCC Part 90: This device complies with Part 90 of the FCC rules for land mobile radio services. Industry Canada: Complies with RSS-119 for land mobile and fixed use. CE Mark: Complies with relevant European directives. Copyright © Kenwood Corporation. For support, contact authorized Kenwood dealer or visit www.kenwood.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Battery depleted/incorrectly installed	Charge battery; ensure proper installation.
No transmission	PTT button/antenna/programming	Check PTT function; verify antenna; check programming.
Poor reception	Antenna/location/squelch setting	Check antenna connection; adjust squelch; move to better location.
Battery drains quickly	Old battery/high power settings	Replace battery; check power settings in programming.
No audio	Volume setting/speaker	Adjust volume; check speaker functionality.
Programming issues	Cable/software/driver problems	Check cable connection; reinstall software/drivers.

Reset: May require reprogramming; contact authorized service center.

Service: Contact authorized Kenwood service center for repairs.