Kenwood VR 2080 Manual

The Kenwood VR 2080 is a high-performance audio/video receiver with Dolby Digital and DTS decoding, 5.1 channel surround sound, 80 watts per channel, multiple audio/video inputs, digital optical and coaxial inputs, AM/FM tuner with 40 presets, learning remote control, speaker setup calibration, and various sound modes. Powered by 120V AC, 60Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Main unit with display panel, Remote Control, Speaker terminals, Audio/Video inputs, Digital inputs, AM/FM antenna terminals.

Feature	Description
Power Output	80 watts per channel (6 ohms, 1kHz)
Surround Modes	Dolby Digital, DTS, Pro Logic
Audio Inputs	6 analog audio inputs
Video Inputs	4 composite video inputs
Digital Inputs	2 optical, 1 coaxial
Tuner	AM/FM with 40 station presets
Speaker Terminals	5.1 channel outputs
Remote Control	Learning remote with macro functions
Display	Fluorescent display with dimmer
Power Consumption	250 watts maximum

Installation

Unpack and inspect contents. Place on stable, well-ventilated surface.

1. Connect speakers: Match polarity (+/-) for all channels (Front L/R, Center, Surround L/R, Subwoofer).
2. Connect audio sources: Use appropriate audio inputs for CD player, tape deck, etc.
3. Connect video sources: Use video inputs for DVD player, VCR, etc.
4. Connect antennas: Attach AM loop and FM wire antennas.
5. Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block vents. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

1. Speaker setup: Use test tone to balance speaker levels and distances.
2. Input assignment: Configure digital inputs for connected sources.
3. Tuner setup: Auto-scan and store AM/FM stations.
4. Sound modes: Select preferred surround mode (Dolby Digital, DTS, etc.).
5. Remote programming: Set up learning functions for other devices.

CAUTION! Keep magnets away from CRT displays and audio tapes.

Specifications

• Power Output: 80W x 5 (6 ohms, 1kHz)
• Frequency Response: 10Hz - 100kHz (+1/-3dB)
• Signal-to-Noise Ratio: 100dB (line)
• Total Harmonic Distortion: 0.08%
• Input Sensitivity: 200mV (line)
• Digital Inputs: 2 optical, 1 coaxial
• Video Inputs: 4 composite, 1 S-Video
• Speaker Impedance: 6-16 ohms
• Power Requirements: 120V AC, 60Hz
• Dimensions: 17-1/8" W x 6-1/4" H x 15-3/4" D

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECTOR, TONE controls, HEADPHONE jack.

Remote: POWER, Numeric buttons, INPUT SELECT, VOLUME, MUTE, SURROUND MODE, TUNER PRESETS, SETUP MENU.

Audio Settings: Bass, Treble, Balance, Loudness. Surround Settings: Mode selection (Dolby Digital, DTS, Pro Logic), Delay time, Channel levels. Tuner Settings: Auto/manual tuning, Preset memory. System Settings: Input rename, Digital input assignment, Display dimmer.

Connecting Devices

Audio: CD player, Tape deck, Turntable (with phono preamp). Video: DVD player, VCR, Cable box. Digital: DVD player (optical/coaxial), CD player (optical).

1. Turn off all components before connecting.
2. Use high-quality cables for best performance.
3. Match input types (analog/digital) to source outputs.
4. Assign digital inputs in setup menu for proper decoding.

Tip: Use optical cables for digital audio sources to prevent ground loops.

Audio/Video Operation

Supports various audio formats and surround modes.

1. Select input: Choose source with INPUT SELECTOR.
2. Adjust volume: Use VOLUME control or remote.
3. Select surround mode: Choose Dolby Digital, DTS, or Pro Logic as appropriate.
4. Mute audio: Press MUTE for temporary silence.
5. Headphone use: Plug into front panel jack for private listening.
6. Tone controls: Adjust bass and treble to preference.

WARNING! Do not operate at maximum volume for extended periods.

Tuner Operation

AM/FM tuner with 40 station presets.

1. Select band: Choose AM or FM.
2. Tune stations: Use auto-scan or manual tuning.
3. Store presets: Hold MEMORY button, then select preset number.
4. Recall presets: Press numbered buttons for stored stations.
5. Stereo/Mono: Auto-switches for FM; manual for AM.

Care & Cleaning

Unplug before cleaning. Use soft, dry cloth for exterior. Use compressed air for vents.

CAUTION! Do not use chemicals or abrasives. Keep liquids away from unit.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power connection; try different outlet.
No sound	Speaker connections/mute	Check speaker wires; ensure not muted; verify input selection.
Poor FM reception	Antenna placement	Reposition FM antenna; ensure proper connection.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear path to sensor.
No surround sound	Input/settings	Verify digital input assignment; check surround mode selection.
Distorted sound	Volume/speakers	Reduce volume; check speaker impedance compatibility.

Reset: Disconnect power for 30 seconds, then reconnect.

Service: Contact authorized Kenwood service center for repairs.