Kenwood VR 305 Manual

The Kenwood VR 305 is a 5.1 channel AV receiver delivering 100 watts per channel, Dolby Digital and DTS decoding, multiple audio/video inputs, AM/FM tuner with 30 presets, remote control, on-screen display, and various sound modes. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 5.1 channel amplifier, Dolby Digital/DTS decoder, AM/FM tuner, remote control, multiple input/output terminals.

Feature	Description
Power Output	100 watts per channel (6 ohms)
Audio Decoding	Dolby Digital, DTS
Tuner	AM/FM with 30 station presets
Inputs	4 audio, 3 video, phono input
Outputs	6-channel pre-out, headphone jack
Sound Modes	DSP modes: Hall, Theater, Stadium
Remote Control	Full system remote included
Display	Fluorescent display with dimmer
Speaker Terminals	5-way binding posts
Power Requirements	120V AC, 60Hz

Installation

Unpack and inspect contents. Place in well-ventilated area.

1. Connect speakers: Use speaker wire to connect front, center, and surround speakers.
2. Connect audio sources: CD player, tape deck, phono to respective inputs.
3. Connect video sources: DVD player, VCR to video inputs.
4. Connect subwoofer: Use subwoofer output for powered sub.
5. Plug into AC power outlet.

WARNING! Ensure proper ventilation; do not block vents. Use correct speaker impedance.

First-Time Setup

Power on receiver; follow initial setup procedure.

1. Speaker setup: Configure speaker sizes and distances in menu.
2. Input assignment: Assign inputs to source components.
3. Tuner setup: Auto-scan and store FM/AM stations.
4. Sound calibration: Use test tone for level matching.
5. Set volume limit: Configure maximum volume if desired.

CAUTION! Turn volume down before powering on to prevent speaker damage.

Specifications

• Power Output: 100W x 5 (6 ohms, 1kHz)
• Frequency Response: 10Hz - 100kHz
• Signal-to-Noise: 100dB (line inputs)
• Total Harmonic Distortion: 0.08%
• Input Sensitivity: 200mV (line), 2.5mV (phono)
• Digital Inputs: 2 optical, 1 coaxial
• Video Inputs: 3 composite, 1 S-video
• Dimensions: 440 x 151 x 380mm (WxHxD)
• Weight: 9.5 kg
• Power Consumption: 280W

Controls and Settings

Front Panel: POWER, VOLUME, INPUT SELECT, TUNER PRESETS, HEADPHONE JACK.

Remote: POWER, INPUT SELECT, VOLUME, MUTE, TUNER, DSP MODES, NUMERIC KEYPAD.

Menu Settings: Speaker configuration, input assignment, tone controls, tuner presets, DSP modes. Audio: Bass, treble, balance, loudness. Video: Input source selection. System: Dimmer, volume limit, factory reset.

Connecting Devices

Audio: CD, tape, phono inputs. Video: DVD, VCR inputs. Digital: Optical/coaxial for digital audio.

1. Turn off receiver before connecting devices.
2. Use quality cables for best performance.
3. Match input types (audio to audio, video to video).
4. Assign inputs in setup menu for remote control.

Tip: Keep cable runs neat and avoid crossing power cords with audio cables.

Audio Setup

Configure speaker system and sound modes.

1. Speaker size: Set front speakers to LARGE or SMALL.
2. Speaker distance: Set delay for proper synchronization.
3. Channel levels: Adjust individual speaker volumes.
4. DSP modes: Select Hall, Theater, or Stadium for different effects.
5. Tone controls: Adjust bass and treble to preference.
6. Loudness: Engage for better low-volume listening.

WARNING! Do not exceed speaker power handling capabilities.

Tuner Operation

AM/FM tuner with 30 station presets.

1. Select tuner input: Press TUNER on front panel or remote.
2. Band selection: Choose AM or FM band.
3. Auto scan: Press and hold TUNING to scan for stations.
4. Manual tune: Use TUNING buttons for precise frequency.
5. Store presets: Hold MEMORY button, then press preset number.
6. Recall presets: Press numbered preset buttons directly.

Tip: For best FM reception, fully extend antenna and position properly.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior. Keep away from moisture and heat sources.

CAUTION! Do not use chemical cleaners. Ensure proper ventilation during operation.

Regulatory Information

FCC Part 15: Class B digital device compliant. CE marked for European compliance. Copyright © Kenwood Corporation. For support, visit www.kenwood.com or contact authorized service centers.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power cord connection; try different outlet.
No sound	Input selection/volume	Verify input selection; check volume level; ensure speakers connected.
Poor FM reception	Antenna placement	Reposition FM antenna; check connections.
Remote not working	Batteries/obstructions	Replace batteries; ensure clear path to IR sensor.
Overheating	Ventilation	Ensure adequate ventilation; clear vents of obstructions.

Reset: Disconnect power for 5 minutes, then reconnect.

Service: Contact authorized Kenwood service center for repairs.