owners manual for a kenwood kdc-bt562u car stereo free

The Kenwood KDC-BT562U is a single DIN car stereo with Bluetooth connectivity, USB input, AUX input, CD playback, and AM/FM radio. Features include hands-free calling, audio streaming, 50W x 4 channels, customizable display colors, and advanced audio controls. Below are key sections for features, installation, operation, connectivity, and troubleshooting.

1. Features at a Glance 2. Installation Guide 3. Basic Operation 4. Specifications 5. Controls and Functions 6. Bluetooth Connectivity 7. Audio Settings 8. USB and AUX Playback 9. Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Bluetooth receiver, USB port, AUX input, CD player, AM/FM tuner, Remote Control, Wiring harness.

Feature	Description
Bluetooth	Hands-free calling and audio streaming
USB Port	For USB flash drives and device charging
AUX Input	3.5mm jack for external audio devices
CD Player	Plays CD, CD-R, CD-RW formats
AM/FM Tuner	30 station presets (18FM/12AM)
Power Output	50W x 4 channels (max)
Display	Customizable illumination colors
EQ Settings	Bass, Treble, Loudness controls
Remote Control	Included for convenient operation
Power Connection	12V DC vehicle power

Installation Guide

Ensure vehicle is turned off before installation. Follow proper wiring diagram.

Disconnect negative battery terminal for safety.
Remove existing stereo from dashboard.
Connect wiring harness following color codes:
- Yellow: Constant 12V (memory)
- Red: Switched 12V (ignition)
- Black: Ground
- Blue: Power antenna/amplifier turn-on
Connect speakers following impedance guidelines (4-8 ohms).
Secure unit in dashboard and reconnect battery.

WARNING! Incorrect wiring may damage unit or vehicle electrical system. Professional installation recommended.

Basic Operation

Power on unit by turning vehicle ignition or pressing POWER button.

Source Selection: Press SOURCE to cycle through modes (Radio, CD, USB, BT, AUX).
Volume Control: Turn VOL knob or use remote control.
Radio Operation: Tune stations manually or use seek; store presets by holding number buttons.
CD Playback: Insert disc label-side up; use track skip buttons for navigation.
Display Settings: Access through menu to change illumination colors and brightness.

NOTE: Unit will enter demo mode if not properly connected to vehicle power.

Specifications

Power Output: 50W x 4 (Max), 22W x 4 (RMS)
Bluetooth Version: 3.0 + EDR
Supported Audio Formats: MP3, WMA, AAC
Frequency Response: 20Hz - 20kHz
Signal-to-Noise Ratio: >80dB
Preset Stations: 30 (18 FM, 12 AM)
Power Requirement: 12V DC, negative ground
Dimensions: 178mm(W) x 50mm(H) x 153mm(D)
Operating Temperature: -20°C to +60°C

Controls and Functions

Front Panel: POWER/VOL knob, SOURCE, BAND, MENU, EJECT, Function buttons.

Remote Control: POWER, Numeric buttons, SOURCE, VOLUME UP/DOWN, MUTE, BAND, Preset buttons.

Menu Functions: BT SETUP (pairing devices), AUDIO (EQ settings), DISPLAY (color/brightness), RADIO (tuning options), SYSTEM (reset/defaults). Audio Controls: Bass (-10 to +10), Treble (-10 to +10), Loudness (On/Off), Balance/Fader adjustments.

Bluetooth Connectivity

Pair mobile devices for hands-free calling and audio streaming.

Enable Bluetooth on mobile device.
Press SOURCE to select BT mode.
Access BT SETUP in menu, select "Pairing".
Search for "KDC-BT562U" on mobile device.
Enter PIN "0000" if prompted.
Confirm pairing on both devices.

Tip: Up to 5 devices can be paired; only one can be connected at a time.

Audio Settings

Customize sound output for optimal listening experience.

Bass/Treble: Adjust frequency response (-10 to +10).
Loudness: Boost low/high frequencies at low volumes.
Balance: Adjust left/right speaker balance.
Fader: Adjust front/rear speaker distribution.
EQ Presets: Flat, Powerful, Vocal, Custom.
Subwoofer Control: If connected, adjust level and crossover.

NOTE: Settings are saved per source mode.

USB and AUX Playback

Connect external devices for expanded media options.

USB Playback:

Insert USB device into front port.
Select USB source mode.
Navigate folders using folder up/down buttons.
Supported formats: MP3, WMA files.
Maximum capacity: 32GB USB 2.0

AUX Input:

Connect 3.5mm audio cable from external device.
Select AUX source mode.
Control playback from external device.

Maintenance

Keep unit clean and free from moisture. Use soft, dry cloth for cleaning.

CAUTION! Do not use solvents or abrasive cleaners. Avoid extreme temperatures and direct sunlight.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Wiring/ignition	Check power connections; ensure ignition wire connected.
Bluetooth not connecting	Pairing/distance	Delete old pairing; ensure within 3 feet during pairing.
No sound from speakers	Wiring/settings	Check speaker connections; verify balance/fader settings.
CD not playing	Disc/format	Ensure disc is clean; check for scratches; verify format compatibility.
USB not recognized	Format/capacity	Reformat to FAT32; ensure capacity under 32GB.
Poor radio reception	Antenna/connection	Ensure antenna fully extended; check antenna connection.

Reset: Hold MENU button for 5 seconds to access reset option.

Service: 1-800-536-9663; www.kenwood.com